Jump to content
SAU Community

R32 Speedo Cable Problems

Dahtone Racing

By Dahtone Racing,
in General Maintenance

 Share

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

lwells Grand Master

lwells

Posted
Posted
$35 in Canberra? Where Lucien????

My cable has been rattling since I've owned the car, and I'm keen to get it replaced...

Not in Canberra, but GaugeWorks in SA. Its $35 to have the inner cable replaced, and a few dollars more to replace the connectors at each end. All up GaugeWorks charged me $58 (inc postage). I sent it on Tuesday and had it back on Friday.

I've just finished installing it, so if you have any questions, fire away.

lwells Grand Master

lwells

Posted
Posted

Fair enough. Its a pretty "simple" job in terms of skills. I must confess I did it the dangerous way with the tyre jack that comes in the boot (highly not recommended if you value your life). Basically goes a little like this:

1. Remove bottom dash. Remove the surrounds from the steering column. Remove the dash surround. Remove the gauge cluster.

2. Disconnect the speedo cable from the dash (it clips in).

3. Disconnect the speedo cable from the gearbox.

4. From underneath the car, look up at the firewall where the speedo cable passes through. There is a rubber triangle with three bolts (10mm; two at the bottom, one at the top). Remove the bolts and pull out the triangle.

5. The speedo cable has a number of plastic cylinders on it that hook on to points of the underbody. Unclip them. You need to feed the speedo cable towards the rear of the car until the end that connects to the speedo is out of the cabin.

6. You will then need to feed the cable towards the front of the car to actually get it out as the rubber triangle is too big to pass all the obstructions when feeding it to the rear of the car.

As I said, pretty simple. All you really need is a jack, a ratchet with 10mm socket, an adjustable wrench (or a spanner of some unknown size) and a phillips head screwdriver.. and some patience :P

  • 2 weeks later...
Jays_5000 Collaborator

Jays_5000

Posted
Posted

May be a dumb question but my mates speedo stopped working then about 10 mins later his power steering cut out and would stay off until the car was switched off, then it would work again for a little while.... Tonight my speedo stopped working then about 10 mins later my power steering did the same thing, is this a common thing too, or just a very weird coincidence?????

heller44 Mentor

heller44

Posted
Posted

It is related.

Where the cable goes into the rear of the speedo module, there is a pickup for ground speed.

No cable rotate : No ground speed signal sent to control modules.

The ~10 mins is the failsafe timeout.

James.

Yidz Experienced

Yidz

Posted
Posted

Made my day too!! :wub:

Ive been driving around with no cable for ages. Took it out cos I buggered it when taking out the dash. Hopefully when I put a new one in, all will be good :stupid:

So sick of turning the car off while driving and then clutching it back on LOL. Every ten minutes.

  • 1 month later...
arbess Experienced

arbess

Posted
Posted

sorry to bring up an old thread, but i just wanted to say that when i repaired my speedo plastic needle with electrical heat shrink, it eventually desintegrated and my speedo failed to work again.

I have since purchased a new gtr speedo cable brand new from nissan at 90 bucks trade price. spent about 2 hours removing and refitting, if anyone has done it, OMFG I HATE THE TRIANGLE BIT.

On a related issue, done anyone have a probelm when the go above a speed limit and the needle kinda "sticks" then moves, "sticks" then moves? ie. its not smooth movement? mine seems to do it after 110. really gay, but not a big issue as im a good boy and stick to the 110km/h limit :D:P

  • 3 weeks later...
Josh_r32 Rising Star

Josh_r32

Posted
Posted (edited)

may be a dumb question but on the dash end of the speedo cable, is the white plastic thingy with the spring inside it ment to be attached to the metal end of the speedo cable housing? or does it just sit in there on top of it freely? i can just pull it straight out??

cheers

Josh

Edited by Josh_r32
Josh_r32 Rising Star

Josh_r32

Posted
Posted (edited)
actually its part of the cable and should not come out if its new.. sounds like you got the problem we have all had... soon it will get stuffed and you will have to let nissan hold onto your wallet.

bye bye

thanks, so if i get a new cable it will come with the plastic bit with the spring inside it etc all attached?

Edited by Josh_r32
arbess Experienced

arbess

Posted
Posted (edited)
thanks, so if i get a new cable it will come with the plastic bit with the spring inside it etc all attached?

yep about 100 bucks. if you check my SIGNATURE, i will have u the part number tonight. about 10pm brisbane time.

Edited by arbess
  • 3 weeks later...
cowie165 Veteran

cowie165

Posted
Posted
On a related issue, done anyone have a probelm when the go above a speed limit and the needle kinda "sticks" then moves, "sticks" then moves? ie. its not smooth movement? mine seems to do it after 110. really gay, but not a big issue as im a good boy and stick to the 110km/h limit :):D

Yep. Yours will probably also do it at really low speeds, like <30kmh

And yeah, totally ghey. I thought it only happened with old speedo cables though? Weird.

  • 1 month later...
dan.1337 Proficient

dan.1337

Posted
Posted

Would the speedo cable be suspect in my case?

This happens 80% of the time when driving. My speedo needle MOVES, but it moves not in accordance to the speed i'm actually doing. So for example, i accelerate to what 60kmh should be and its hovering around the 180-190+ mark. If i do 100, it moves all the way round and stops at the bottom of the rest pin.

Once in a while it'll go back to normal and show the correct speed. Then 5 mins later it's doing crazy stuff all over again.

I also have no idea how to get the cluster out to check it. Is there a tutorial on this?

cowie165 Veteran

cowie165

Posted
Posted

Yes and yes. :rolleyes:

Tutorial to get your dash cluster out:

http://www.skylinesaustralia.com/forums/in...howtopic=115618

Haven't seen one for replacing the cable but there are lots of threads with references to doing the job.

HTH

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Matt Z
      SAU NSW - Chickos Cruise

      By Matt Z · Posted

      Scenic roads, stunning skylines, and Chickos to finish it off! Join SAU NSW as we cruise through the Royal National Park and along Lawrence Hargrave Drive to Figtree! Sunday 26th October 2025 4:30PM Meeting Waterfall Station Parking 5:00PM Cruise Departure Royal National Park > Lawrence Hargrave Dr > Memorial Dr > Sid Parrish Park 6:15PM Arrival at Sid Parrish Park Figtree Meet Location: Waterfall Station Parking Final Destination: Sid Parrish Park RSVP: https://forms.gle/E4s5SiRKQfDdypky8 *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • MBS206
      "Cheap" bolt on turbo on RB25DET NEO

      By MBS206 · Posted

      It's funny, as Ive seen plenty of people use them in cheap builds on YT. And they actually go okay, even though a lot of other maxspeedingrods stuff is terrible. Those turbos seem reliable enough, the only part being, a good quality turbo that is "identical" to it, will out perform it day in and day out. In both a lower boost threshold, and the ability to flow more air at the same boost pressure. As a cheap cheap replacement, not a terrible choice. For cheap and shouldn't blow in a day, not terrible (like other eBay/Temu turbos) for low cost and still decent performance, that's where the question comes in to play from the results I've seen. I'd actually find it hilarious to buy one, and strap it to a paddock basher or some other cheap as POS originally NA car, and send it to the moon!
    • tylink720
      "Cheap" bolt on turbo on RB25DET NEO

      By tylink720 · Posted

      The maxpeedingrods turbo is cheap and bolts on to stock parts. I think you just need a bigger silicone coupler for the intake. Its a cheap china turbo, but it's been running on mine for almost 3 years at 16-19 psi.
    • MBS206
      Strange issue RB25DET wont start

      By MBS206 · Posted

      What do they look like right after you've tried to start it with everything connected? Also post photos of what they actually look like.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Also wanted to say, my new spark plugs are blackened looks like it's very rich. I have splitfire coilpacks but stock coilpack loom and ignitor. I tried directly grounding the ignitor ground to body as well. 
×
×
  • Create New...