Jump to content
SAU Community

R32 Speedo Cable Problems

Dahtone Racing

By Dahtone Racing,
in General Maintenance

 Share

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

lwells Grand Master

lwells

Posted
Posted
$35 in Canberra? Where Lucien????

My cable has been rattling since I've owned the car, and I'm keen to get it replaced...

Not in Canberra, but GaugeWorks in SA. Its $35 to have the inner cable replaced, and a few dollars more to replace the connectors at each end. All up GaugeWorks charged me $58 (inc postage). I sent it on Tuesday and had it back on Friday.

I've just finished installing it, so if you have any questions, fire away.

lwells Grand Master

lwells

Posted
Posted

Fair enough. Its a pretty "simple" job in terms of skills. I must confess I did it the dangerous way with the tyre jack that comes in the boot (highly not recommended if you value your life). Basically goes a little like this:

1. Remove bottom dash. Remove the surrounds from the steering column. Remove the dash surround. Remove the gauge cluster.

2. Disconnect the speedo cable from the dash (it clips in).

3. Disconnect the speedo cable from the gearbox.

4. From underneath the car, look up at the firewall where the speedo cable passes through. There is a rubber triangle with three bolts (10mm; two at the bottom, one at the top). Remove the bolts and pull out the triangle.

5. The speedo cable has a number of plastic cylinders on it that hook on to points of the underbody. Unclip them. You need to feed the speedo cable towards the rear of the car until the end that connects to the speedo is out of the cabin.

6. You will then need to feed the cable towards the front of the car to actually get it out as the rubber triangle is too big to pass all the obstructions when feeding it to the rear of the car.

As I said, pretty simple. All you really need is a jack, a ratchet with 10mm socket, an adjustable wrench (or a spanner of some unknown size) and a phillips head screwdriver.. and some patience :P

  • 2 weeks later...
Jays_5000 Collaborator

Jays_5000

Posted
Posted

May be a dumb question but my mates speedo stopped working then about 10 mins later his power steering cut out and would stay off until the car was switched off, then it would work again for a little while.... Tonight my speedo stopped working then about 10 mins later my power steering did the same thing, is this a common thing too, or just a very weird coincidence?????

heller44 Mentor

heller44

Posted
Posted

It is related.

Where the cable goes into the rear of the speedo module, there is a pickup for ground speed.

No cable rotate : No ground speed signal sent to control modules.

The ~10 mins is the failsafe timeout.

James.

Yidz Experienced

Yidz

Posted
Posted

Made my day too!! :wub:

Ive been driving around with no cable for ages. Took it out cos I buggered it when taking out the dash. Hopefully when I put a new one in, all will be good :stupid:

So sick of turning the car off while driving and then clutching it back on LOL. Every ten minutes.

  • 1 month later...
arbess Experienced

arbess

Posted
Posted

sorry to bring up an old thread, but i just wanted to say that when i repaired my speedo plastic needle with electrical heat shrink, it eventually desintegrated and my speedo failed to work again.

I have since purchased a new gtr speedo cable brand new from nissan at 90 bucks trade price. spent about 2 hours removing and refitting, if anyone has done it, OMFG I HATE THE TRIANGLE BIT.

On a related issue, done anyone have a probelm when the go above a speed limit and the needle kinda "sticks" then moves, "sticks" then moves? ie. its not smooth movement? mine seems to do it after 110. really gay, but not a big issue as im a good boy and stick to the 110km/h limit :D:P

  • 3 weeks later...
Josh_r32 Rising Star

Josh_r32

Posted
Posted (edited)

may be a dumb question but on the dash end of the speedo cable, is the white plastic thingy with the spring inside it ment to be attached to the metal end of the speedo cable housing? or does it just sit in there on top of it freely? i can just pull it straight out??

cheers

Josh

Edited by Josh_r32
Josh_r32 Rising Star

Josh_r32

Posted
Posted (edited)
actually its part of the cable and should not come out if its new.. sounds like you got the problem we have all had... soon it will get stuffed and you will have to let nissan hold onto your wallet.

bye bye

thanks, so if i get a new cable it will come with the plastic bit with the spring inside it etc all attached?

Edited by Josh_r32
arbess Experienced

arbess

Posted
Posted (edited)
thanks, so if i get a new cable it will come with the plastic bit with the spring inside it etc all attached?

yep about 100 bucks. if you check my SIGNATURE, i will have u the part number tonight. about 10pm brisbane time.

Edited by arbess
  • 3 weeks later...
cowie165 Veteran

cowie165

Posted
Posted
On a related issue, done anyone have a probelm when the go above a speed limit and the needle kinda "sticks" then moves, "sticks" then moves? ie. its not smooth movement? mine seems to do it after 110. really gay, but not a big issue as im a good boy and stick to the 110km/h limit :):D

Yep. Yours will probably also do it at really low speeds, like <30kmh

And yeah, totally ghey. I thought it only happened with old speedo cables though? Weird.

  • 1 month later...
dan.1337 Proficient

dan.1337

Posted
Posted

Would the speedo cable be suspect in my case?

This happens 80% of the time when driving. My speedo needle MOVES, but it moves not in accordance to the speed i'm actually doing. So for example, i accelerate to what 60kmh should be and its hovering around the 180-190+ mark. If i do 100, it moves all the way round and stops at the bottom of the rest pin.

Once in a while it'll go back to normal and show the correct speed. Then 5 mins later it's doing crazy stuff all over again.

I also have no idea how to get the cluster out to check it. Is there a tutorial on this?

cowie165 Veteran

cowie165

Posted
Posted

Yes and yes. :rolleyes:

Tutorial to get your dash cluster out:

http://www.skylinesaustralia.com/forums/in...howtopic=115618

Haven't seen one for replacing the cable but there are lots of threads with references to doing the job.

HTH

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...