Jump to content
SAU Community

Recommended Posts

Hi all,

Some fool crawled under my r33 gts-r (na), unbolted and took off with my muffler; I was parked at Doolandella on friday night for a few hours. The guy prolly lives near there since I go there a fair bit on the weekends. It a pretty rare muffler so I’d like to locate it if possible, it’s a Trust, mild steel (not stainless steel) with a 4inch outlet (not sure), sorry no pics of it. You might have seen me driving along the Centenary HWY to and from UQ St Lucia on the weekdays. I’m a poor ass science student doing my pHD and I really loved that muffler. I’m currently not driving my skyline since I can’t afford to get a new muffler; does anyone have a stock muffler that they would like sell/give away? Anyway if anyone notices my old muffler, can you post up where you saw it?

Thank you

post-25296-1134612626.jpg

post-25296-1134612666.jpg

I bought a Trust muffler from a guy (on these forums) in South Brisbane but that was a few weeks ago and mine is stainless steel.

BTW, what's an R33 GTS-R?

Make a wanted to buy thread if you havent already. I'm sure someone will be willing to give/sell you theirs. I've got my stock muffler sitting in the garage but was hoping to hang onto it. If you can't find anyone willing to sell theirs let me know and I'll consider letting go of mine because I know I'd hate to have my muffler stolen, thats f**ked!

Try and find a pic of your stolen muffler so people know what to look out for. Hope you get it back buddy!

BTW, what's an R33 GTS-R?

naturaly aspirated.. non-turbo.. didn't have the extra dosh to bring a proper one in

If its got a 4inch outlet or bigger and it ain't stainless steel chances are it might be mine.. its not a perfectly circular one either, it was flat along the top i think

Thanks

Edited by neoncandy

huhuhu...

holy crap I hope my one didn't cost as much as this one... mild steel is definately cheaper right? any way this is the closest one that i could find which looks like mine, it got trust in big words on the under belly too. The outlet is exactly like mine but I'm not sure if it was that big... maybe... it wasn't a cannon either.

post-25296-1134616591.jpg

i heard of a guy who had his inntercooler, bov and some piping flogged off his car.

I heard you had your virginity stolen....

I know i was tricked....

Back to topic.... Tonight we had a can of jim beam taken from the passangers seat of my mate ute... We were sitting on the back of the tray and someone took my last can from the esky on the passengers seat....

Bastards... Bloody school holidays...

Lucky they didnt see the brand new pioneer head unit still in box on the floor....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...