Jump to content
SAU Community

Recommended Posts

i did a bit of a search for any info on modding the L24 engine on here, and i couldnt find a thing :)

so anyway, how should i go about giving my L24 some balls?

i got quoted around $900 for a set of extractors + full 2 1/4 inch exhaust, still gotta have a bit of a shop around on that though.

im also guessing a bit of a carbie upgrade would make it feel a bit better.

any other idea.. and also any ballpark figures of what itd cost to do??

hopefully i can get a bit done after xmas :D

Link to comment
https://www.sau.com.au/forums/topic/98957-l24/
Share on other sites

a 2.4L, OHC , Straight six.

came in c210 skylines and 240z's among other things..

While they both share the L24 designation, in fact their performance is very different. Small port/valve head and low compression + single carb really emasculated the L24S (S=single carb) in C210 (I'm assuming you still have the stocker). My advice would be to ditch the L24 entirely and get an L28. Then put in a cam, bump compression a little, fit a free flowing exhaust and perhaps a set of 240Z carbs and you'll have something that will have performance worlds away from your current setup.

If you must stick to the current L24 then try to find a head from an r30 Skyline, which will give roughly the same CR, but have bigger ports/valves and allow the engine to breath. Then fit exhaust/carbs/cam as per L28 above. Flat top pistons from 240Z L24 can be used to bump compression.

Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1802261
Share on other sites

the best for you money would be to get a complete L28, a good head such as a N42 or P90, get your carbs re-calibrated so that they can flow enough for the bigger motor, and a full exhaust. This should give you a big upgrade in power and torque.

I have a 280ZX which i have just swapped an RB into and also a 260Z with a L28 in it.

BTW - where are you located?

Edited by nissan_280zx
Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1804105
Share on other sites

the best for you money would be to get a complete L28, a good head such as a N42 or P90, get your carbs re-calibrated so that they can flow enough for the bigger motor, and a full exhaust. This should give you a big upgrade in power and torque.

I have a 280ZX which i have just swapped an RB into and also a 260Z with a L28 in it.

Unfortunately your L28 won't fit his C210 - the sump bowl is in the wrong place. Z's have a rear bowl sump, but 240K/C210/R30 (not to mention R31/R32/R33/R34) have a front bowl sump. Something which I should have mentioned before.

It's possible to modify the sump and particularly the pick-up to fit, but it's not a simple 'bolt on' proposition.

Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1804205
Share on other sites

the best for you money would be to get a complete L28, a good head such as a N42 or P90, get your carbs re-calibrated so that they can flow enough for the bigger motor, and a full exhaust. This should give you a big upgrade in power and torque.

I have a 280ZX which i have just swapped an RB into and also a 260Z with a L28 in it.

BTW - where are you located?

Im located in Penrith (nsw)

Whats the difference with the heads?? (n42, P90, etc)

and also, what do they come off?

Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1804233
Share on other sites

  • 3 weeks later...

what you can do is stroke it, (dont know where to get the crank from but) or much easier way would be to

1. shave the head

2. over size valves/ flow head.

3. cam / lumper

4. 3 webbers (prick to tune) / injection setup.

5. exst

should really haul then. thats pretty much what my L20 had for my 1600.

Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1851170
Share on other sites

Really I have seen a l28 straight into a l24 r30 and was told that it was a simple conversion?

There are basically 2 types of L28 in terms of sump configuration - front sump bowl or rear sump bowl. R30 needs a front sump bowl configuration, but 280ZX has rear type so it won't 'bolt in' without fairly substantial mods.

Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1851233
Share on other sites

  • 2 weeks later...

I got the $1000 exhuast and cam work on my l24 it hauls arse but mine is injected!!I got lightened flywheel when i changed the clutch car goes heaps hard .....Put your thousand bucks towards buying this

http://www.skylinesaustralia.com/forums/in...howtopic=102996

Its a r30 sedan with 9 inch wide 3 piece simmons

Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1892312
Share on other sites

Have you run it down the quater yet? i want to run mine i have no idear what time i am even capable of. My only problem is the launch above 3500 grand wheelspins when the clutch gets dropped. but at 3200 it does a f**ken great launch but it is hard to get it rite.

Edited by datzla
Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1894933
Share on other sites

Hmmmm.....

Some interesting posts in here.

1. If you are going to install an L28 just bolt the L24 sump and pickup onto it... I have done it with no probs.

2. best value for money would be Extractors and Twin SU Carbs.....these will make a HUGE difference to an L24 - the head on a C210 is a closed combustion chamer type so whatever you do - DO NOT PLANE THE HEAD - you will get a much better result buy putting in 1mm oversized flat top pistons.

3. There was some talk of stroking.....if you are talking about stroking an L24 then that is easy.. just get L26 or L28 Crank and Rods. If you are talking about Stroking an L28 then forget it ....serious $$$$$$ are needed.

TG

1978 Datsun Skyline C210 Rally Car

L28

Autronic EFI

Lots'a'grunt

Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1908357
Share on other sites

I am lingering on the same notion of an L28 N/A upgrade for my mr30 skyline.

my friend has a 240k, as said before their heads have small ports and their compression is high but their flow is crap.

here are some random facts;

*going efi will straight up make a noticable difference, although i'm not sure whether efi is compattible with earlier l24heads such as e30-31 heads. they come stock with e88 heads on mr30 skylines.

*p90, p92 and other heads of the same type were used on the turbo model 280z's. they have a compression of around 7.00:1 i think.

*e-series heads usually have high compression but have really bad flow.

*n-series heads such as n42 and n47 are ideal for non-turbo setups because they have high compression and high flow. when looking for an N-series head go to U-pullit and look through all their Mr30 skylines, most have e88 heads- what mines got(they're still better than e30,31 heads), but you should be able to find some n42/n47 heads amongst them. i think it costs about 80-110 for a block or head individually from lonsdale and elizibeth U-pullits. and there should be plently of mr30's there.

Blocks:

L24- alright for a bodge turbo setup

L28- excellent for N/A. if you're looking for a straight on conversion with an L28 head, then get one WITH FLAT-TOP PISTONS. -even higher compression.

*an L28 block with flat-top pistons and an n42 or n47 head will get you a whopping compression level of 9.5 to 10.5 depending on how it's setup. which is so high you'll be running premium.

*'apparently' there isnt too much difference between the restriction of L28 manifolds to L28 extractors, but i cant comfirm this.

*the efi used on L24 and L28 engines should be interchangable.

*if you go with an N/A setup consisting of an L28block-flat-top pistons and an N47 head-ported, with a 2 & 1/4 exhaust and EFI'd you'll be looking at about 180-190hp at the flywheel i think. maybe more.

if you play your cards right you shouldn't be paying too much for this upgrade assuming that you do it by yourself.

EDIT: also as stated before you will also want the cam grounded, i think 2x1000rpm - 7x1000rpm would be an ideal powerband.

*although this all seems well and good, the hardest thing to get your hands on would probably be an F54 block. they are sought after by datsun enthusiasts.

Edited by Blue Dynamite
Link to comment
https://www.sau.com.au/forums/topic/98957-l24/#findComment-1909391
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...