Jump to content
SAU Community

Recommended Posts

Hey guys,

I seen some where if u drop RB26 rods and crank into your car it should turn it in a 2.2litre RB20.....is this true, i think it is but im wondering will these just drop in with no other mods......and is it really worth the work and money for an extra .2 of a litre.

How much would it cost and is it worth it?

- Luke

Link to comment
https://www.sau.com.au/forums/topic/99363-rb20det-to-rb22det/
Share on other sites

Dont see how...

I mean i did a JUN 2.2 kit on my second GTS-X and the crank was totally different to a stock rb26 one...

I just dont see it turning in that little bore. I mean the counter waits...

I dont think the rb26 bearing will fit the rb20 block in fact im sure they wont. Also you can't use the rb20 bearings as their smaller on the big ends....

Anyways by the time you get these parts you will have spent enough money to pay for a full JUN kit brand new...

I paid AUD $3400 for the kit when i was in japan on holidays.

The kit included pistons, crank, rods, bearings & rings.

I also purchased cams and other bits and pieces to suit at an extra cost.

Edited by Col-GTSX

yes it can be done, tomei supplies pistons to suit a 2.2l rb20 that is achieved by boring the motor to 82mm.

rb26 bits DO fit but the block has to be clearanced for it to fit.

using rb26 bits (crank, rods, bearings) and special pistons (tomei in this case) gives you a 2.4l rb20 with a capable 9k redline due to the rb26's better crank and rods...........

but like i said above tomei does sell 82mm pistons to bring it out to a 2.2 using stock rods.

Edited by carl h

This is a very common topic, do a search on RB23 and RB24.

Here is one of my posts on this subject....

Hi guys, I will try and answer the questions, but before I do I should point out that you can swap most of your good bits onto/into an RB25DET and end up with a better result than building an RB23/RB24. And it will cost a damn site less as well.

On to the questions;

The standard RB20 bore is 78 mm, the most common RB23 (2,280 cc's) piston upgrade is 4AGZE which are 81 mm (from memory). This means you will need to relieve the combustion chambers radius at the bore by 1.5. Then taper it into the normal combustion chamber shape. Pretty simple really, any machine shop could do it.

You will need to relieve the combustion chamber volume to achieve your target compression ratio. From memory about 3 cc (slightly more than a good polish) gives 8.8 to 1 for an RB23. The combustion chamber volumes will have to be equalised of course.

Porting is pretty much essential if you want to use the higher rpm effectively without huge amounts of boost. There is a lot of work on both the inlet and exhaust ports needed. If you do a really good job, you should end up around 85% of what a standard RB25 cylinder head flows.

Depending on the experience of the machinist and the workshop hourly rate you are looking at around $1K to do the above.

There are larger valves available for RB20's , I have seen 2mm larger inlet valves and 1.5 mm larger exhaut valves. I have a recollection that they were for a VG30 or CA18 but they fit the RB20. Since VG30's are popular in the US there are quite a few valve, valve spring alteratives. A quick check of the sizes should confirm the suitability.

From memory the VG30 valves where around $US20 each, so that's $640 for the set plus freight.

RB26 cranks vary considerably in price, I have seen R32GTR cranks around $400, rods around $200. Up to double that for R33GTR cranks and rods. The best suggestion I can make is to shop around the For Sale forum and check out the historic prices.

As for cams, 256 to 264's would be fine for using with the hydraulic followers (260 Poncams for example) . But to really use 272's or higher you would need to do a solid follower conversion. No, RB26 bits won't fit, well not without some serious engineering and machining. But CA18/VG30 may well fit, worth checking anyway.

By the time you have the necessary RB23/RB24 parts purchased, get it all machined and assembled you are looking at a bit over $5K. Then you have to add the accessories, manifolds, turbos etc.

Hope that was of some help

:D cheers :)

So sydney kid wat your saying is that most of your rb20 good parts will bolt into a RB25?? like if i went out and bought a rb25 would my rb20 tomei cams fit straight in...and how would i get my gtr injectors to work or even fit.....could i still use my ap engineering power fc with this motor...and my rb20 splitfire coilpacks??? if all this stuff fits im gettin one next week :D

depends where your from. Terry from kansai automotive here in adelaide is getting his shipment very soon, stocking some RB26 cranks and conrods.....i think he's using an Rb20 to test the conversion himself, bores it out to roughly a 2.3 ltr withou pistons.....coz u dont actually need to change pistons, but if the cash is there...DO IT! Give Kansai an email and he should hopefuly help you somehow. www.kansaiautomotive.com.au or just .com cant remember, i practically live there lol so i never go no the site

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...