Jump to content
SAU Community

Recommended Posts

hey boys and girls,

deciding on a new pair of shoes - Speedy Wheels - Envy HP

what does everyone think of them? probably get a set of 18" with +38 offset, got a quote of $1995 on some Sona SX1 tyres or $2300 with Toyo tyres...

any suggestions/recommendations?

ps. anyone has photos of those wheels on anything? i'm putting it on r33 s2

:P

post-24624-1135304525.jpg

just make sure offset and width suit the car, you want to make sure they'll fill the guards properly.

http://product.permaisuri.com/Content/Prod...&strBrandID=132

above is a great site for different wheel styles, have a look at some of the stuff Work has to offer, Work VS-SS or Volk GT-C's are great

I think those rims would look good on a lancer, not a skyline.

However, 8" with a +35 or a +38 (like these ones) would be a perfect fit for an R33.

Deep Dish looks horn

Makes the car look like a stock car so to speak

We have 9.5 on the rear and 8.5 on the front, the car isn't lowered and no scraping issues either.

we run 275 on the rear 235 on the front.

here is a pic, gotta lub tha fat rubber.....

very nice madmanz. are they from tempe??

oh by the way for some reason my rear left wheel scrapes the guard... don't think other cars do this though?? im using 35mm king springs

Edited by MintR33

Yeah mate got those from Tempe Tyres

The skyline is up at stock height that is why we don't have any problems with it, but if you lower the car i rekon thats when there is problems!

very nice madmanz. are they from tempe??

oh by the way for some reason my rear left wheel scrapes the guard... don't think other cars do this though?? im using 35mm king springs

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
    • He means "as opposed to mechanical cable drive". Older cars (R32 for ex.) had cable drive. Later cars with essentially the same gearbox, ie R34 GT (NA RB25) used essentially the same box as the R32 GTSt, but instead of a cable drive, had an electronic speed sender plugged into the same hole in the box, running from the same little gear that would have run the cable. Some of the shittier later cars use a speed sender on the nose of the diff, or the ABS sensors.
    • Lower than engine, or lower than it should at the hubs? Either way, that is a nice power figure and I'm not surprised you say it rips now. What stopped you from turning it up any more? Injectors? Or did it just stop responding to boost?
    • Got my 34 gtt tuned last week. Car made 362 wheel horsepower at 19 psi. Turbo was the ATR43SS. Only other upgrades were haltech 2000 series. 650cc injectors, walbro 250, fmic. Pro hub dyno reads 6% lower than actual figure according to my tuner. Car is a real ripper now.  IMG_7261.mov
    • Hi everyone, I'm wondering if anyone in Melbourne (preferably West) has a non-S2 R34 front bar. If it's already off the car, even better!  Nothing too weird, I just need to get a cut-out of the hole that the front indicators clip into 🤣 (image attached for reference)   I've got a front bar from JSAI Aero, but those holes need to be cut myself, and I want to get it right so the indicators will clip securely. And my OEM bumper is a S2, so I have no reference. So looking for a member who might be able to spare me a few minutes to make a cardboard cut-out using your front bar.
×
×
  • Create New...