Jump to content
SAU Community

Recommended Posts

The last couple of days have been really hot 30deg +.. And I have noticed my 040 intank pump is a noisier than usual. It is like it is cavitating or the pump is out of the fuel constantly.. Quite loud.. Before the last couple of day I could barely hear it. I also have a inline fuel pressure guage on the pump side. What I noticed is the guage oscillating +- .1 psi .. To my it seems like the fuel is like froth from all the heat and driving around. It is the only thing that make sense to me.. It also makes my idle real bad :D

Anyone has any ideas? am I right by the froth idea? if so how to stop it.

Link to comment
https://www.sau.com.au/forums/topic/99654-noisy-bosch-040-pump/
Share on other sites

I have a 910 external.

Mine used to be so noisy it would vibrate the floor pan even though it was rubber mounted. Upon feeling the out fuel hose it was vibrating so much it made my hand feel slightly numb.

I ran a dedicated feed from the battery via a relay to the pump.

It is still noisy but can no longer be felt or heard inside the car.

tank was 1/4 full...

Busky2k: you find the pump noisy on hot days only? usually I can't hear it..

Driver: brand new pump.

I took the pump out bench tested it.. I noticed the pump to be really quite..mm strange.. The only time I could get the pump to be noisey was when it was starving for fuel. To do this I stood the 040 upright with the suck side on the floor - then it was noisy.. Which was making the same sound could I could hear in cabin..

the pump is high enough from the bottom of the tank. So the only thing I could think of is maybe pressure is not being release from the tank properly on hot days and the pump is struggling to pump the fuel out..

any ideas?

hmm I'm starting to hear mine too. I have a Bosch 040 internal and you can hear it when acc is turned on, briefly before the engine is started. I could barely hear it when idling standing next to the car. The past couple of days has been hot and I can start to hear the pump alot more. I'm not really worried about it but I'll keep an eye out for any updates on this topic.

Nath

I found the problem... Crap in the fuel.. It is my worst nightmare going back into the tank - headaches and start seeing stuff :D ..

I took the pump out and noticed heaps of black crap on the filter.. I cleaned it up and it was soundless for 20 ks of driving.. So I used the old pump without a filter and draind and put back the fuel with the 040, 7 times - until no crap was found in the fuel. It seems to be ok now.

When I installed the 040 I also used the original filter and when I took the 040 pump out of the tank I found the black stuff stuck in the 040 filter - it was getting through the original filter. So the 040 filter is finer than the old filter thus picking up more crap before the filter in the engine bay..

I think maybe I got a bad batch or the heat has cleaned the tank off and left floaties..

argh! I just flushed the tank 7 times - shake the car take fuel out and filter the fuel back in. After 40 ks and a top up of fuel the pump is noisy again :P .... I think the petrol station down the road has bad fuel..

I dont think I can take the take out as it looks crammed under the diff..

Oh well another flush tomorrow..

what am I doing posting! I should be drunk!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...