Jump to content
SAU Community

Recommended Posts

I wouldn't want it going much past 100-110degree's.

95degree's is fairly warm, Bl4ck32 has an oil temp guage it sits pretty much level with water temp, being ~83-85degree's.

One difference between yours and his is the lack of piston oil squirters, having piston oil squirters removes heat from the piston, possibly why yours is a little higher.

Which oil temp guage did u get? one with a elec sender? How much I need one. :D

Edited by Cubes
Link to comment
https://www.sau.com.au/forums/topic/99711-oil-temp-warning/#findComment-1816126
Share on other sites

thanks Cubes, i think ill set it at 105C.

all up the whole setup cost more than i wanted to spend i bought each part in stages.

Blitz DCII electronic Temp guage $200

Blitz Live-Unit II $135

Blitz Sandwich plate (goes between oil filter & block) $100

Link to comment
https://www.sau.com.au/forums/topic/99711-oil-temp-warning/#findComment-1816140
Share on other sites

I've done 1,000km in the past 3 days (all 30-35c days with plenty of humidity) and my oil hasn't gone above 90c (according to the factory oil gauge in my r32 gtr, which being 11yrs old im not sure how accurate it is). That's with air intake temps of 50-55c and water temps of 76-85c.

I've certainly done plenty of hard driving (altho only at 11psi) and heaps of freeway driving.

Link to comment
https://www.sau.com.au/forums/topic/99711-oil-temp-warning/#findComment-1816563
Share on other sites

Ive got a Series 1 GTS-t putting out around 270kw and the Water Temperature reading on the Power FC never goes above 81* except during a 3 lap Supersprint when it goes to around 98* and cools down to 81* within 4 mins of driving slowly. I have a Electronic Omori Oil Temp Guage fitted and an Oil Cooler and the Oil Temp never gets above 70* except during a 3 lap Supersprint when it gets to around 100* and it cools back to 70* within the 4 minuite cooldown as well. This was with the Standard Radiator which I replaced with a PWR thicker one and no differece has been noticed. Also running tank water with Water Wetter in the system.

I think 98* normal running seems too hot and I would get the cooling system flushed.

Ian

Link to comment
https://www.sau.com.au/forums/topic/99711-oil-temp-warning/#findComment-1816741
Share on other sites

If your hitting 110+ degree oil temps on the street then you should look at fitting an oil cooler, no if's no buts.

Apparently at 115degree's the high oil temps begin to break down the petroleum oils and cause oxidation, which in turn forms deposits, varnish and increases wear.

Edited by Cubes
Link to comment
https://www.sau.com.au/forums/topic/99711-oil-temp-warning/#findComment-1816768
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...