Jump to content
SAU Community

Doing My Homework

LTHLRB

By LTHLRB,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

LTHLRB Grand Master

LTHLRB

Posted
  • Author
Posted (edited)

ah right right, do gtr injectors fit in the std rb25 fuel setup and would i need an ecu if i upgrade them? i know that with the rb30's its u haveto change the ecu if u have the injectors. But im not too sure on the rb25 ecu.

Edited by LTHLRB
Jetdat Veteran

Jetdat

Posted
Posted
According to HPI stock r33 injectors are only 370cc/min and as such run out of flow at around 200rwkw.

really???

i have about 200rwkw with standard injectors and the are nowhere near their max duty cycle...

i think they are only at around 70%...i thought 250rwkw was achievable with standard injectors??

also dont believe everything you read in magazines, rather talk to people with experience...

boj01 Experienced

boj01

Posted
Posted
aren't SR20 injectors side feed as well?

Yes, SR20 injectors are also side feed. You will need to buy larger Sard/Nismo/Bosch/Denso injectors if you want an upgrade as there is really no standard injectors that are an easy side feed upgrade.

cogs Experienced

cogs

Posted
Posted

I thought I read S15 injectors (side-feed) were a straight fit on R33 GTST? They aren't 550cc but they are higher than r33 std 370cc, maybe 470?

Also GTI-R SR20 injectors are top-feed and some side-feed SR20 injectors are only 370cc so same as R33, so if you go sr20 make sure you get the right ones.

LTHLRB Grand Master

LTHLRB

Posted
  • Author
Posted (edited)
Well how much power are you chasing?

If Jetdat is right then you can get 250rwkw with std injectors.

The most i can get in standard from, standard being ecu, bottem end, cams. Maybe around 200 - 250 rwkw. Ultimately in the long run around 300 350 rwkw using a 35/40 and maybe rb30 bottem end rebuilt with steel rods and forged pistons and a good set of cams.

Edited by LTHLRB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...