TCO

If i recall correctly you're looking for "Strut Bar To Chassis Mount Bush Kit". Superpro have a listing for it on their website

I don't think I've ever seen one with an aerial there. As Scotty said the OE ones are built into the rear side glass. Did it have an aftermarket HU installed before you purchased it?

This? http://nissan.epcdata.ru/stagea/nm35/6839-vq25det/engine/213/ http://nissan.epc-data.com/stagea/nm35/6839-vq25det/engine/213/

Drivers side there's a grommet through the firewall with wiring, easiest I found. Use a long heavy duty cable tie / stiff piece of wire (carefully) with the line taped to the end. BOV is located on the intake piping just before the throttle body. Has a largish diameter pipe heading off in front of the plenum and a small diameter tube connected to the plenum.

Models with an N are AWD, without are RWD

Nah it's you can either order them from UAE (Cheaper, longer to arrive, usually more expensive shipping) or from Japan (More expensive, quicker to arrive, usually cheaper shipping).

What issue are you trying to resolve? Nissan will be hit an miss depending on the parts guys enthusiasm (Morphett Vale guys are pretty helpful). I've bought a bunch of bits and pieces via Amayama, shipped from both UAE and Japan warehouses. Reasonably quick with replying and shipping etc.. haven't had any issues yet, just have to make it worth the shipping.

Are you looking for OEM rubber replacements or poly bushes? If you're just after OEM bushes you could try a Nissan spares at a dealership part# is 54613AL520 *some* are actually helpful and are happy to order parts (others not so much). Alternatively purchase via Amayama etc.. Best to order a few items to make it worth the shipping cost (although i've found their shipping Japan->Aust warehouse to be very reasonable). Other option is upgrade...

1. Import Monster / Jesse Streeter (Amayama//RHD Japan/ Just Jap for new parts) 2. Audio controls should be fine - I beleive Josh just did an install, check out the what have you done thread, there was some aftermarket cruise options... 3. $6XX Full comp with glass from SGIC 4. Compression Rod Bushes 5. 29mm sounds about right 6. Is it the standard pop-up screen or one of the other options / aftermarket that was available on these. Stock popup would be a headache without the rest of the gear already in there.

Mine has side/curtain airbags: ACCS3, COAT2, COLD2, ETCS2, HRSTH, ROOF3, STERW I got a whale spec NM35. Original owner went a bit over the top with the options catalogue.. Reverse camera Front & Rear parking sensors Rear license plate surrounds Woodgrain trim Cargo area light Folding/Dipping mirrors Indicators on mirrors Wind deflectors And a bunch of other bits a pieces

That looks right from what I recall, as long as your head unit can handle resistive controls and you can teach it what the buttons do you're all good. If not you'll need an Axxess ASWC-1 or PAC SWI etc.. adaptor. I grabbed an ASWC-1 when i was going to drop a single DIN cheapy in but ended up going a different route.

(W)Z411 has the same seal and seam diameter as the Z436 it's just a bit taller. Either of the ones you bought is fine to use.

Yeah that'll be it

As Dale said you'll also need part# 27500-AL502 (AC Controls) which is the expensive bit. Usually cheaper to find a complete double din unit from a wreck or yahoo japan.

If that head unit is like mine should have wires in the loom labelled key1 / key 2. Tap into that connector red to key 1, green to key 2 and yellow to ground. Speaking of which, in what was perfect timing my factory Bose unit died (at least the AC was stuck at 18°) . It'd been playing up for a few months, not playing nicely with the Grom USB2+. Luckily I'd already gathered the required replacement parts and had them sitting there ready. Cheap Chinese Android head unit with a PAC ROEM-NIS2 interface unit (because i'm lazy)

Wood grain trim comes up regularly on yahoo auctions for reasonable prices. Also note there's different coloured wood grain so if you buy separately make sure it's correct.

Tan Trim colour code will be "E" That sucks, hope you track it down

Few places in the engine bay - stamped on a plate near the drivers side shock mount, second line NM35-XXXXXX or on the firewall behind the engine.

+1 Dump that stock junk and hit Scott up for the mod. Definitely one of the essentials.

If you want to avoid the metra kit (i don't blame you they look and feel like junk). Your best bet would be to get an OE double DIN fascia from (Yahoo) Japan via Import Monster or Jessie Streeter. e.g: http://page7.auctions.yahoo.co.jp/jp/auction/g164554402

Could be. Attached is the output I got from Hobdrive. Temps look right and RPM was correct, would have to go for a drive to see if speed was being reported. Elcheapo elm327 knockoff i have was sold as "V1.5 Super Mini ELM327 OBD2 OBD-II Bluetooth CAN-BUS Auto Diagnostic Tool" but that was a few years ago. Link in my ebay account directs to a v2.1 device (looks identical though)

I tested out the Hobdrive trial and it did work, it was a while ago so can't recall what data was available. Pretty sure it was up and running with my knockoff elm327 (also have an OBDlink MX WIFI so could have been that). If i didn't have an Informeter Touch already i probably would've coughed up the $27 for it and given it a proper testing. +1 have an Informeter & sensor harness (with boost & oil pressure/temp sensors). Very handy to have it all there in a nice small package.

Yup my bad, other set is x8

Series 1 AR-X rims are 18x8 +30something (38?)

Took a quick measure, won't be entirely accurate but close enough to give you an idea..... Dash to Boot Door (closed): 2840mm centre console to boot (seats flat): 2000mm seat (rear) back to boot: 1120mm between wheel arches: 1040mm between opening at the base (from the top of the corner): 730mm widest width of the boot: 1380mm height at opening: 760mm max height of the boot: 770mm