Ryno

I have both my sway bars set at medium. I first installed these as the only mod to the standard suspension, and noticed a massive improvement - with very little under steer. I have since installed everything else in Sydneykids package of goodies, and made another step forward in the cars handling. However, now at the limit, it tends to under steer a little. As such I am now considering stiffening up the front sway bar to hard, to dial this out. Thoughts?

Hey George, I had the same problem when I installed my whiteline front sway bar. The best I could get in the end was the bush being slightly offset with the bracket (one side of the bush sits about 5mm outside the bracket). This was a concern at first, however after 6 months of driving, the bush hasn't budged. Ryno

Hey Andrew, I'm in NZ on holiday at the moment. When I get back I'll send some better pictures to all those interested, so you can work out if it's what you're after. Cheers, Ryno

Price drop - $200 - All parts included

Defence

Hey mate, There was no need for me to roll my gaurds, as they're not rubbing anywhere. I went down to 225/45R17's on the front so they wouldn't rub on the upper arm, but the rears are still 235/45R17's. Ryno

It's about 335mm (though my left front is 342mm for some strange reason).

Hey Sydneykid, Just had all the suspension gear installed today, and I'm stoked with the result. The ride height is spot on (I used the standard Bilstien circlip setting), now I just have to hope I don't scrape my exhaust of a speedbump or the like... Thanks again, Ryno

Ooops, posted in the wrong topic

Parts arrived today... Thanks Sydneykid!

Also have a 2" silicone 45 deg bend, and 2" to 1" stainless reducer pipe to enable plumbing back in to the original pipework.

Greddy Type R BOV (for RB25DET) - $300 This BOV is in good condition. I planned to install it on my car, but after seeing the shear size of it I'm thinking it may be overkill for my intended power output. Item is located in Nowra NSW.

The advertising for them states: "They are machined from virtually unbreakable Duravar® UHMW Polyethylene. These mounts are much harder than polyurethane or rubber and will never wear out." If they fit my car, they should work well... They have no metal parts to them, so they should have minimal road noise.

Yeah that would be cool - if it's not too much hassle. I've purchased these mounts (pictured below), and have been told they fiy S13/S14/Z32, I assumed they would fit my R32 as well. If it looks like they wont, I may have to jump onto your group buy. Ryno

Any idea what the difference is between the R32 and R33 bushes?... I thought they were the same

My thoughts exactly, the boss could be useless.

Hey Buddy, The streering wheel can be bought new on ebay, for a little over $200. I may be interested, if you can be a little realistic with your price, and post some actual pictures of the wheel. Cheers.

PM Sent

How much are you after for the whole loom then?

Yeah it's hard to tell on the photo alone, but it looks like it's on there. It should have two circular plugs on it, that have an internal diameter of 10 -15mm. I believe they are the only circular plugs on the loom.

Do you have the loom with the two plugs, that connect to the knock sensors? I don't need the whole engine loom, just the plugs for the knock sensors so I can wire them in.

Hey fella's, I'm after the loom with the two plugs that connect to the knock sensors. I do not need the whole engine loom, as I will wire the knock sensors directly to the computer. Cheers, Ryan

Double post.... Bugger

Hey Adrian, Do you have the loom with the two plugs on it for the knock sensors? I do not need the whole loom, as I will wire them directly to my computer.

Do you have the wiring loom that plugs into the two knock sensors?