Jump to content
SAU Community

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

R32 = Hotcakes

R33 = Rolling tumbleweed

Probably due to the fact r33s are so common and now you can get compliance for $1200 the market is flooded.

We don’t like to touch 33s for this reason unless it’s a nice colour, manual and overall in very good condition

On the other hand the 32s looks like people can’t get enough. We still get calls for 32s that we sold a month prior.

And it is this reason you can buy a 33gtst for 14k and cheaper and 32 gtst for about the same price.

$1200 compliance? wtf?

Yep, there is something like 80+ workshops doing 33s at the moment. So add another $300 for tyres and you have a full compliance.

Edited by Mecha

Sorry I don’t know all my 33 info off by heart, we don’t do that many of them (we do mainly euro stuff).

But the $1200 price is a definate.

True but I think you may need a separate certificate to comply them.

You nee a separate certificate for 2 door, 4 door, gtr etc except for non turbos which can be brought it.

Sorry I don’t know all my 33 info off by heart, we don’t do that many of them (we do mainly euro stuff).

But the $1200 price is a definate.

True but I think you may need a separate certificate to comply them.

You nee a separate certificate for 2 door, 4 door, gtr etc except for non turbos which can be brought it.

roflafagus... $1200 for R33 compliance... $1200 for a 15 year old R32 maybe. And wtf different price for S1 and S2... that's a new one. You don't do many of them, yet you charge half the going price anywhere in Australia? That dosen't add up.

I'd like some concrete evidence of this to believe it, and if its true then this compliancer will be getting a shit load of work.

OK,

Well I got some more info; compliance doesn’t matter if it’s S1 or S2.

We can DEFINATLY get it done for $2200 + tires so even in this case it can be done cheaper.

And I have been told from a VERY reliable sources that it can now be done for $1250 (not $1200 like I previously said) + tires, but I guess this price is not 100% confirmed as we have not had the chance to bring in a 33 and get it complied there.

Either way if someone was to import a 33 through us we would defiantly follow this $1250 price up. Worst case scenario you can get it done for $2200.

Still a saving.

And I have been told from a VERY reliable sources that it can now be done for $1250 (not $1200 like I previously said) + tires, but I guess this price is not 100% confirmed as we have not had the chance to bring in a 33 and get it complied there.

Either way if someone was to import a 33 through us we would defiantly follow this $1250 price up. Worst case scenario you can get it done for $2200.

So how much would it cost to get a 1998 R33 Series 2 GTS25t though you guys from start to finish?

lol, im not offended, i just think its stupid to say that they are the least desireable, and everyone has them, in the same sentence no less..

Maybe he means less desireable in terms of looks?

Most people don't necessarily buy R33s because they think they look better, you'll find most people like the look of R32s and R34s. But when talking about the GTST/GT-T market, its hard to go past the R33. Unlike the R32, its RB25 equiped, more spacious also its almost as good as an R34 and much cheaper. So the most pracitcal/cost efficient choice becomes the R33, hence their popularity.

Also compliance for $2200 is cheap. I had my old 33 done for $2500 w/o tyres, about a year ago.....the workshop wouldn't do R34s by any chance Mecha? I'm thinking about importing one soon....

Also $1250? wow. that would be cheap, but i don't think it can be done, 15yo compliance is at least 1000 bux these days.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...