Jump to content
SAU Community

Recommended Posts

Maybe he means less desireable in terms of looks?

Most people don't necessarily buy R33s because they think they look better, you'll find most people like the look of R32s and R34s. But when talking about the GTST/GT-T market, its hard to go past the R33. Unlike the R32, its RB25 equiped, more spacious also its almost as good as an R34 and much cheaper. So the most pracitcal/cost efficient choice becomes the R33, hence their popularity.

Yer spot on... I preferred the look of the 32 and 34 over the 33. But I was happy to settle for a 33 which has more to offer in other areas.

I think you have come one step closer to deciphering the ultimate question of some 32 drivers: "WHY would you buy one of those TAXIS!?" :lol:

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Guest Mashrock

driving a 33 is more about the wank factor that "i drive a skyline"

i used to get the whole "race my skyline its the fastest" when i drove the gti-r..

after about 15m you never herd from them again.

but i guess that would be also generalizing them right?

on the other note. i would just say that there are too many of them out there. and too many people tyring to do the same thing. and also because of these new rules there seems to be a cutdown of younger "hoons" and their ease of getting into a car thats quicker than "billy's" commodore.

Edited by Mashrock

there definatly is a wank factor with most people deciding to buy skylines, but for some it purely is performance. for some its a bit of both. it's the majority spoiling it for the minority. people just wanna look cool driving about, its nothing new the yanks were doing it since the fifties.

still, that dosent just apply to skylines, s13's, 300zx's, supra's, even commodores suffer the posing factor.

posing wouldnt be such a bad thing if it didnt involve the usual challanges, slagging of other peoples cars and the general 'act like a tool' culture that goes with it.

Guest Mashrock
prolly just as many if not more 32's....its not our fault they dont stand out :(

some kind of puke factor??

:P

haha f**k i'm going to stop.

my comment made before was probably not called for. but its the same across the board with every car. there are always going to be dickheads involved..

i.e. look at me.

"Beauty is in the eye of the beholder"

To me that means an R-32 - to others an R-33 - whatever floats your boat.

Just don't slag somebody else for their tastes (sounds utopian doesn't it ;-)

np mate, it was all in fun...im sure even you can appreciate a nice 33...i really dont like 32's, mainly the rear, but when i see 1 that i like i can still say "ooo nice 32..."

:P

lol me either, and i hate the rear of 32s as well.

as a matter of fact, R32s have become a new generation of posing cars coz somehow everyone thinks a R32 goes faster than a R33. and thats y they are so popular nowadays.

back to topic, skylines have created a very bad public impression 'skylines=hoons'. so ppl are trying to stay away from them. eventually ppl will realise how good they are.

imo, commonwhores are more likely to be hoons than skylines...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...