Jump to content
SAU Community

Recommended Posts

Are you still gettng a decompression gasket? I wouldn't bother. Grepin's getting well over 300rwkw with standard compression and pistons.

shit 300rwkw!!!!

no headgasket for now as the labour to install it is more than the cost of the gasket

  • 2 weeks later...
' date='15 May 2006, 03:53 PM' post='2168293']

well, i just had a talk to my tuner and he told me i should be maybe to make 300rwhp @ about 1.2barish :

how much power are u guys making?

You sould go way past 300rwhp!!!

also don't get too down if it doesn;t make the power as every freakin dyno in this country reads different.

im not too worry about the power, as i really only want 300 to 330rwhp but im just starting to get worry that my engine may die :

i guess i just got to wait and see

You're probably looking at around 260-270rwkw @17psi with that setup and good tune, a bit worried about your chinacopy FMIC :D

And this should be fine on stock internals if you use 98ron fuel and keep oil nice and clean :rofl:

BTW, what fuel pump will you be using?

Edited by Color_Of_Green

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...