Jump to content
SAU Community

Recommended Posts

  • Replies 717
  • Created
  • Last Reply

Top Posters In This Topic

Only 3 more sleeps to go :D Can't wait... I'm eager to see what difference in power I will get - hopefully it's not too big considering the last dyno tune was 2 weeks ago :P

Anyways, IMPORTANT NOTICE:

All forum members attending this official SAU NSW event, who are not SAU NSW Members yet - please consider joining up on the day. A lot of hard work has gone into organizing events such as this one - all support (primarily through memberships) would be most appreciated to keep the club going strong!

Thanks

S

:P

darn, 2 and half more bloody days, :D

I have a missed match wheels at the rear,

1 is 255/45/17, the other is 225/45/16 ( stock r32 rim)

going to be alrite?

my other wheel at MAGman shop atm.

his takin his time! :)

If both of those tyres were new the first would 2.08 metres in circumference and the second 1.91 metres. That doesn't sound safe let alone able to be put on the dyno.

Could you put another stocker on there?

i MIGHT not be able to make it to this. Steering rack has to come out as my power steering completely shit itself on sat night. Felt a slight shudder, HICAS light came on, smoke started pouring out from under the bonnet, out from the front left wheel arch and from out the back. Steering rack just started squirting out oil =/

So it will be a mad rush to see if i can get it done by then

If both of those tyres were new the first would 2.08 metres in circumference and the second 1.91 metres. That doesn't sound safe let alone able to be put on the dyno.

Could you put another stocker on there?

FACT: Smaller diameter tyres/rims make more power on a dyno.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...