Jump to content
SAU Community

Recommended Posts

  • Replies 717
  • Created
  • Last Reply

Top Posters In This Topic

Only 3 more sleeps to go :D Can't wait... I'm eager to see what difference in power I will get - hopefully it's not too big considering the last dyno tune was 2 weeks ago :P

Anyways, IMPORTANT NOTICE:

All forum members attending this official SAU NSW event, who are not SAU NSW Members yet - please consider joining up on the day. A lot of hard work has gone into organizing events such as this one - all support (primarily through memberships) would be most appreciated to keep the club going strong!

Thanks

S

:P

darn, 2 and half more bloody days, :D

I have a missed match wheels at the rear,

1 is 255/45/17, the other is 225/45/16 ( stock r32 rim)

going to be alrite?

my other wheel at MAGman shop atm.

his takin his time! :)

If both of those tyres were new the first would 2.08 metres in circumference and the second 1.91 metres. That doesn't sound safe let alone able to be put on the dyno.

Could you put another stocker on there?

i MIGHT not be able to make it to this. Steering rack has to come out as my power steering completely shit itself on sat night. Felt a slight shudder, HICAS light came on, smoke started pouring out from under the bonnet, out from the front left wheel arch and from out the back. Steering rack just started squirting out oil =/

So it will be a mad rush to see if i can get it done by then

If both of those tyres were new the first would 2.08 metres in circumference and the second 1.91 metres. That doesn't sound safe let alone able to be put on the dyno.

Could you put another stocker on there?

FACT: Smaller diameter tyres/rims make more power on a dyno.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • It's not any meta data. They have scraped images from everywhere, and then use AI to compare your photo to other photos and work out where you are.
    • I just looked at my camera phone settings, apparently I have "not allowed" for location  Will that stop that app?
    • Can you not just turn it off on your phone if required? I remember a brief on this, well, I remember the brief, not what to actually do. LOL
    • Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
×
×
  • Create New...