Jump to content
SAU Community

Recommended Posts

  • Replies 103
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...
  • 4 weeks later...

i did have a bit of trouble adjusting at mallala - i noticed where i used to be able to stay in 3rd on the front straight - i'd have to shift to 4th with the 25 box. BUT now i just decided to start my entries earlier and clutch it in 3rd lol...

BTW - the reverse lights do work - i re-clipped mine in and they both work good as new.

r33 are 3.79 though, i might pull my diff out and suss what it is before i worry to much about ratio's :spank:, there are ups and downs of going either way atm so im a lil up in the air which i should buy (r32 box or r33)

edit: im pretty sure the diff in my car is only a s13 type so at a guess the ratio would be 4.08:1?. and i thought 4.3 were auto gearsets? :ninja:

Edited by toffy

nah all R32's were 4.38 auto and manual

ca turbo s13 were also 4.38

with a 20 with a 25 box I'd say you'd need the short ratio still

with a 25 motor and box or a stroked 20 the sr s13 ratio might be better

all depends on the track you go to most though to

cheers for that info, mainly i go to baskerville which is mainly a 3rd gear track first turn is right at the top of third (140ish?+?) you hit the apex at around 115-120 and bounce the limi and scando for the next turn which is about 95-100 at the apex which is a down hill section s bend thingy coming out of that is a short straight which leads into another left hander that opens up on the exit to an up hill straight to munji as fast as you can :laugh: , im worried that if i have a shorter 3rd i wont have the speed for a big enough entry in turn 1 which is vital in comps and the exit corner and straight you need just as much speed really :laugh: :laugh:

  • 2 months later...
  • 5 weeks later...
would be good if I had a part number for a 33 speedo cog though

O rly?

32743-30P20- (Just the cog on the end)

Now it'd be good if I had some money...

post-11389-1180679868_thumb.jpg

32744-35F00 - generic nissan

post-11389-1180680317_thumb.jpg

post-11389-1180680326_thumb.jpg

post-11389-1180680336_thumb.jpg

Edited by TonyL
i have a 33 box with the speedo drive... i need to get the navara drive lol... also gotta replate that plastic drive behind my dash.. cause its rooted

i've still got the name of that place in wingfield that can apparently make metal ends for the cable - haven't been there yet though because... well silvias are electric so i dont give a f**k :lol:

whats the chassis code for navara?

Note: i haven't read any of this thread :cool:

Edited by TonyL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...