Jump to content
SAU Community

Recommended Posts

Hey fellas,

Im pretty new to this site so if ive f**ked up somehow with the way ive added this topic feel free to write me off.

Anyways, My R33 gtst has recently been fitted with a new rb25det 97 model motor. It has turbo back exhaust, front mount, k and n pod, boost to 12psi, dump and front pipe and a hi flow cat. KYB struts and hard coils and 235 reo40 tyres.

The question is how far off staying level with a stock r33 or r32 gtr it is? the reason I am asking is if it is a fair way off, I have the money ill piss it off and by a gtr.

So a bit of advice would be appreciated guys. what 400m time could i expect with these mods? high 13s?

Thanks again, This site is great im learning a lot from it

If you're going to modify a car up, you always start from the model that has all the bits you're not planning on replacing.

For Skylines, that's the GT-R since nothing else comes with the hydraulic ATTESSA and its way too expensive to retrofit it on a lower model. You don't necessarily need to look for a V-Spec or N1 if you're planning on replacing the brakes / turbo etc, but that stuff's bolt on compared to the drivetrain.

You might be able to keep up with a stock R32 / R33 GT-R (I'm assuming in a straight line, around the bends its still going to disappear on you), but good luck finding a stock GT-R on the roads.

If you are prepared to spend another $5k you can get some great fun out of your R33..

Don't buy an old 89/90 model GTR for $22k if that is what you are thinking. I wouldn't spend too much less than 30k to get a good R32 GTR

ive owned an 32 and 33 gtst and most recently had an r33 gtr. when the gtr was all stock except removed boost restrictor and HD clutch it ran 12.8@106. the gtst's i had, had mods similar to yours and would not even come close to the gtr.

as much as I loved the gtst's, once i sat in the gtr I knew that I would never go back... go the gtr if you can!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
    • That's some really horrible design with the way it's cut/shaped! Is there much damage to the box that failed in? IE, new fork and you can go again, or is it a total rebuild again? Id be trying to build that piece from scratch, and getting some reliefs added in the corner to hopefully stop breakage, and then swapping boxes ASAP, and then doing the same to the currently good working box. I'm assuming hard shifts have not been friendly to it!
×
×
  • Create New...