Jump to content
SAU Community

Recommended Posts

Just to post the ****ing obvious. I just finished building my car and it finally goes good. Now I have no ****en license. New laws are in place ppl and they ****ing hurt, a 2 second hold of my accelerator netted me a 12 month suspension. YAY FOR ME!

Just a warning, i never thought it would happen but hey... these new laws do not mix with cars like skylines :P

Peace out and cya all in a year.

Link to comment
https://www.sau.com.au/forums/topic/10434-speeding-watch-out/
Share on other sites

yup, its way to easily... thing is you can accelerate to 100km and stop to 0km in about 150m in a skyline... more than any other piece of crap commonwhore on the road.

To me 10km/hr isn't that much over the limit (very little difference in safety), and yet you can pay for it for a long time .. and its now 3points

Was it a radar ? Undercover? Which suburb? Sorry to hear, but these are the things we need to know :P

Damn man... Sorry to hear it. The new laws are fairly tight, but not much we can do about it now I guess, they're already in place. :P

I fear driving on the Ring Road due to those 'Measuring speed over time/distance' cameras they apparently have along there now...

And if only the money being raised from all these damn fines went to things like road repair, driver education, etc..

:)

-Ross

Throwing down $0.02

As you go under a first bridge they record your speed.. they then measure the time it takes to get to the second one.

If the time taken to get to point B is greater than the speed limit you get pinged by a camera and sent a fine.

Revenue raising at its truly worse. Saves about zero lives too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...