Jump to content
SAU Community

Recommended Posts

your best options would be the pfc, dont waste you time with anything else!!!!!!!!

steve

Cost would be a factor.

AP engineering Power FC ( required for an RB20 ) would be around $1300-$1400 plus tuning of $450 ish.

Remap including supplying the necessary board hardware is around $880 all up including tune.

Any retuning is based on an hourly rate same as tuning any computer and both Lucas's Bikiroms and Glenn's Lumpyroms have had considerable success in high power applications .

Lee Sampsons 470 rwhp SR20 DET and 11.18 1/4 mile on a Lumpy rom is testament to that.

Or Adam Trewhellas RB25 Cefiro with 365 rwhp and stays on the rev limiter for most of the Wanners drift track.

Only down side is in WA you are limited to the 2 shops above as Denver mentioned so if you hate us both , your in trouble for retunes :P

Cheers

Ken

spoke to hyperdrive about it.... sounds pretty good. only downside i guess is cost of reprogramming when upgrading components.

didnt really want to spend 2k on pfc .

does 300hp@ wheels sound a bit far fetched? (already have gt2530 and gtr injectors)

spoke to hyperdrive about it.... sounds pretty good. only downside i guess is cost of reprogramming when upgrading components.

didnt really want to spend 2k on pfc .

does 300hp@ wheels sound a bit far fetched? (already have gt2530 and gtr injectors)

Cost of retuning is no different than any other computer. Rate is $140ph on the dyno and takes about the same time as tuning an Autronic/motec/wolf/power FC.

300rwhp is achievable , I have 290rwhp in an RB20 with low mount and external gate.

( Well I did till the turbo blew on Saturday night :) )

Cheers

Ken

One of our custom made hiflo ones using a stock R33 GTS-T turbo.

No mods to be needed and dump bolts straight up. $1600 which sounds expensive except every other turbo avaliable requires dump/intake or water line changes.

We weld the gate up and run external gate mounted on a stock manifold.

Relatively cheap but a little laggy atm until we sort of few other things out.

And yes , it is on stock internals and running 16-17psi.

Cheers

Ken

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...