Jump to content
SAU Community

Recommended Posts

First thing to check. did you renew any of the rear steering arms when you fitted the hicas rack - I presume you fitted the old arms to the hicas lock bar. If you did then do the following...

Jack up the rear of the car to get wheels in air, support on stands and then grab the wheel at a quarter-to-three, try to move the wheel(as the rear steering would have). If you have any movement at ALL then you will most likely need the bushes in the rear hub replaced and the rear steering arms too.

I had Fulcrum at Rocklea do mine in my GTS4 and a mates GTR, they did a pretty good job plus they now have jigs to fit the bushes from doing my car.

Also check that the rear subframe bushes aren't stuffed, the ones behind the doors are silicone filled and the ones near the spare tyre well are solid rubber. The solid ones don't normally cause a problem, just the front ones - which Noltec make.

Good luck

Edited by gts4diehard
Link to comment
https://www.sau.com.au/forums/topic/106288-r32/#findComment-1966692
Share on other sites

yeah i replace the arms with new ones when did the lock bar they looked a little sused ime thinking its the front bushes it looks like there is marks from where the subframe has been hitting the chassis rail any one out there who can help with this

Link to comment
https://www.sau.com.au/forums/topic/106288-r32/#findComment-1969365
Share on other sites

yeah i replace the arms with new ones when did the lock bar they looked a little sused ime thinking its the front bushes it looks like there is marks from where the subframe has been hitting the chassis rail any one out there who can help with this

Get a big screw driver and lever the subframe around, if it moves then you have a problem. Look at the 4 main subframe to chassis mounting bushes, they are filled with silicone. Make sure none iof them is leaking.

They are marked with green dots in the attached picture;

R34_GT_R_Rear_Suspension.jpg

If the bushes are stuffed you can either replace them with polyuretthane bushes, Nismo harder rubber and alloy. This is a big job as the subframe has to be removed from the car. A less expenive (DIY) job is to fit a set of Whiteline rear subframe bushes (AKA pineapples), to supprt the damaged standard bushes. They are around $115 and can be fitted in 20 minutes.

;) cheers :)

Edited by Sydneykid
Link to comment
https://www.sau.com.au/forums/topic/106288-r32/#findComment-1970558
Share on other sites

anyone out thee have solid urathane mounts in there 32 and can let me know whats it like getting conflicting storiesone suse told me that its that harsh i wont be able to even see out the mirrors

even more cool is if someone in brisie has this done can take me for a spin just to ease the questions any help much appricated

Link to comment
https://www.sau.com.au/forums/topic/106288-r32/#findComment-1981943
Share on other sites

Most of the guys with rear subframe bush issues simply add the Whiteline rear subframe alignment kit (pineapples)for ~$115. It is a 20 minute DIY and doesn't add very much NVH at all ie; most people don't even notice it. Much easier and cheaper than removing the whiole rear subframe and pushing out the standard bushes.

:biggrin: cheers :biggrin:

Edited by Sydneykid
Link to comment
https://www.sau.com.au/forums/topic/106288-r32/#findComment-1982478
Share on other sites

Most of the guys with rear subframe bush issues simply add the Whiteline rear subframe alignment kit (pineapples)for ~$115. It is a 20 minute DIY and doesn't add very much NVH at all ie; most people don't even notice it. Much easier and cheaper than removing the whiole rear subframe and pushing out the standard bushes.

:biggrin: cheers :biggrin:

but what if the std bushes a f**ked

Link to comment
https://www.sau.com.au/forums/topic/106288-r32/#findComment-1982512
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hope it's actually possible. This is a write off in insurance world.
    • Yup. 2-way with shallow ramp angles. Still works.
    • That was the first session so not a lot to take from the day. It was low 20s ambient and the coolant had got to 110 (and obviously had some pressure!) so that still needs to be addressed. I haven't downloaded the data yet but will. I had refilled the auto trans with Redline DT6 because it claimed the best viscosity I could find at 100o. It wasn't really long enough to get a good feel for that; while the trans got to 100o in the session it still wasn't shifting crisply as I hoped. I think I'll try a few more sessions before judging. No steering motor overheat but I'd hope not in only 1 session! But finally the suspension; it was night and day over the standard stuff and the car was a couple of seconds quicker on the same crappy tyres, which is a huge difference. I'll stick with that and get some sway bars and a mechanical diff sorted too and see how that all goes together
    • I guess it’s partially a compromise of how my car is used, wanting to be able to switch from drift to grip with track side on-car adjustment. Also partially with the way the knuckles are set there is more static camber but less dynamic camber gain. 
    • OK, so update from the track day on Friday It was a classic "an unfortunate series of events'. There were a few cars around and when i checked my mirror coming out of the fish hook I notice some smoke from the rear of mine. Looked again and it was getting much worse, I figured I'd blown a turbo or something to got off it and pulled off the racing line. However.... since it is a left hairpin into a right kink, I was on the inside of the next corner. There was a car passing me on the left and a big drop off over the ripple strip on the right......and someone had knocked the witch's hat that was on the apex about 1m onto the track. So, between those 3, I decided to mow down the cone and not damage my car/the other car. Right choice, but surprising result.  The car decided the cone was a small pedestrian so it blew the rear bonnet hinges up to protect their head in the upcoming person to car impact....I didn't see that coming and like an airbag deployment it happened super fast. Straight into the pits from there, everything was driving fine but it became clear it was a coolant leak not smoke, it was billowing up onto the windscreen. Onto the trailer and home. I'll do a separate thread about the repair (once I work out what it is ), but the immediate problem was the bonnet wouldn't open because the front was pinched onto the front bar and would not release. Ultimately we unbolted the hinge from the bonnet, pulled it back a little and it released from the front OK. "There's your problem", the top radiator hose had popped off at the radiator.
×
×
  • Create New...