Jump to content
SAU Community

Recommended Posts

I used the Stagea pump, bracket (I slotted the rear-most mount bolt to make it easier to install with the twin turbos), and crank pulley. Seemed like the easiest solution and has worked for just at a year now without problems.

Ah ha you put the RB25 crank pulley on th RB26 to line up, that makes sense, thanks.

  • 2 weeks later...
I am currently doing an RB26dett manual transplant to my previously RB25det s1 auto Stagea, here's a few pics, let me know if you need any more pics (R33 handbrake mounting, R34 clutch pedal & master install etc.) and I'll try and post them as it's still in the process of conversion........

Have you started to work out the wiring side of things yet?

I am starting to think this is a better way to go than keeping the Rb25. Have been looking into this conversion a bit more lately.

Did you lift the motor and box in from below or did you feed it in from the top?

Have you started to work out the wiring side of things yet?

I am starting to think this is a better way to go than keeping the Rb25. Have been looking into this conversion a bit more lately.

Did you lift the motor and box in from below or did you feed it in from the top?

I have the various Stagea / GTR wiring diagrams and have been scribbling notes on them as to which wires need to go where, but have not as yet started to physically cut wires and unwrap looms. I am still doing the final mechanicals, currently sorting out a rear GTR 4.11 LSD and driveshaft conversion to match the new GTR front ratios and upgrade to LSD rear.

I should get to start the wiring in the next few weeks so I'll post up progress and pics as I go. I would also like to hook up the GTR's front torque split gauge but haven't had a look at the wiring for that yet, and I have a torque split controller to wire in at the same time.

If anyone out there has any RS260 wiring diagrams please post them up! (I will swap you some hen's teeth! lol)

I pulled the motor and box out from the top and the same to put the 26 & manual in............see pics....................

post-65070-1255070197_thumb.jpg

post-65070-1255070455_thumb.jpg

post-65070-1255070682_thumb.jpg

post-65070-1255071038_thumb.jpg

  • 2 years later...
  • 1 year later...
  • 2 years later...

bump

has anyone got wiring diagrams for the rb26 engine loom to ecu and to what wires in the s1 stagea needs to be redone to get the rb26 to work with

and the wiring of the plug for the auto to manuel gearbox

thanks

Edited by Big Ozone

bump

has anyone got wiring diagrams for the rb26 engine loom to ecu and to what wires in the s1 stagea needs to be redone to get the rb26 to work with

and the wiring of the plug for the auto to manuel gearbox

thanks

I would think you need the RB26 loom and ecu. For the auto wires look in the DIY section above in the manual conversion thread.

I would think you need the RB26 loom and ecu. For the auto wires look in the DIY section above in the manual conversion thread.

Yes I do know I need a rb26 engine to ecu loom as I have that it's the wiring of that loom to the stagea std loom I need a diagram of.

And as for the auto wires I've had a look in the manual conversion thread and can't find the relevant post

Post No 1 first pic:

DSC05438.jpg

Post No 1 below last pic:

Go back to the front of car with the four plugs. The two pin grey plug is your inhibitor switch, put a loop between those (cut plug off auto trans loom). The brown plug is for the reverse lights (well two pins of it anyway), hook those up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...