Jump to content
SAU Community

Recommended Posts

Max Power about your XR6t I unfortunately work at Adrian Brien Ford, I have seen this happen alot. We had a staff member whos bought a turbo for her husband, it had some clutch problems they wouldn't do it under warranty - this caused a lot of problems around the place as the are so F***ing lazy when it comes to warranty work.(sorry you can probibly tell that I absolutely hate my job and work but this is the truth about warranty work in dealerships they make more money out of the customer than they do Ford)

I hope my warranty works as i had to come home from the cruise early as my clutch is playing up!

Edited by Whiplash
I hate to say it whiplash but the clutch want come under warranty because it is classed as wear and tear I think. I had to replace mine myself $4500 later. :D

wot u put in it a OS geinkin (spelling :S)

and did u do the work your self

i just got Kent brake and clutch to do mine and cost 800or 900 i cant remeber of the top of my head i think 900 for the GTS-4 with a HD xtreme clutch

BOUGHT MY CAR FROM rEDLINE AND I CANT SAY I HAVE HAD ANY PRBS WITH IT.... u DO PAY A LITTLE EXTRA FROM THEM BUT AT ELAST YOU KNOW YOUR GETTING A HALF DECENT CAR (MINE HAD THE AUCTION PAPERS AND STUFF COME ALONG WITH IT.... hAVNT HAD ANY PROBS AT ALL AND WHEN I GOT RAA CHECK THEY FIXED THE STUFF THAT WAS WRONG APART FROM MY REAR SPOILER LIGHT BECAUSE Icbf.

i went into redline a few weeks ago, looking around for my first skyline...however, i've been lurking round for a while checking out prices, and yeah they did seem a little expensive, 2-3k more than other places.

also, you'll be kinda hard pressed to find a GT-R there. the only one i saw was an R32. a lot of 32 and 33 GTS-T's, and most of these were pretty clean.

they're pretty good if you want a supra or 180sx as well, and one thing that i did notice that the brakes on a lot of the cars were very rusty, so that's something you probably should take into consideration when you look to buy...brakes aren't cheap.

and one thing that i did notice that the brakes on a lot of the cars were very rusty, so that's something you probably should take into consideration when you look to buy...brakes aren't cheap.

new brake pads allways go rusty when i got new pads in my car i would get up and over night there was a rust like residue over my rotors

i dont think that is too much to worry about

A good option is interstate purchases, with RTA inspections and such .. They pick up pretty much everything and more in the way of faults. I saved myself quite a few thousand just by going interstate and driving it back (after taping up the front to prevent stone chips). I could've got it transported but how better to check a car for driving faults than driving it back from Sydney?

I went through http://www.japimports.com.au/ and found Brad Host to be a good, honest dealer. Couldnt be happier with my purchase, he even drove it to the airport for me to pick it up :happy:

They sell aftermarket warranties too for a reasonable price, not that I have had a need but I have called the firm querying. They cover almost everything, clutch, diffs, even exhaust :P

Maybe not relavent to the topic, but a possible other option :(

A good option is interstate purchases, with RTA inspections and such .. They pick up pretty much everything and more in the way of faults. I saved myself quite a few thousand just by going interstate and driving it back (after taping up the front to prevent stone chips). I could've got it transported but how better to check a car for driving faults than driving it back from Sydney?

Interesting option, but do different states have different rules regarding compliance and what is and isn't legal?

For example, if I bought a car that was complied in VIC could it be possible that it is infact illegal in SA due to different laws? I am new to all these rules and regulations so please correct me if I am wrong..

Cheers for the link though!

^^^ yes that is spot on the money my opinion if u dont want to go over the pits @ regency is buy local

but it is a very good option too if u dont mind a visit to regency least it doesnt need full compliance i believe

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GCG is a good company, they're a major distributor for Garrett in Japan as well.
    • Nah, OEM washer bottle and brake fluid reservoirs are fine I don't know what it is with the plastic that Mazda used, some plastics, like the washer bottle and brake fluid res are fine, and still look new after 20 years use, where as the coolant expansion tank, and PS reservoir, that I replaced with new OEM items when I first got the car, turned yellow and started getting brittle a few years later If the dirty yellow stained plastics didn't trigger me there wouldn't be an issue, but they did, much like the battery bracket....... Meh As for going back to work full time to support car stuff, nope, why, because I own a Mazda NC MX5, not a Nissan R series Skyline 🤣
    • I've never heard of CJ-motor, so can't advise you on them. I'd just go straight to GCG for a GCG highflow though. Seems no point to use a middleman. I'm somewhat surprised that the price on the CJ site is lower than the GCG retail price. Even though CJ would get a discount of some sort, you would hardly expect them to give up so much margin. Maybe the price is out of date? Having said that "I'd go to GCG"...when I did my highflow, I went to Hypergear. I did this https://hypergearturbos.com/product/rb25dethighflow/#tab-dyno-results with the R34 OP6 450HP profile. With the BB centre (extra $400) and intially with the standard boost actuator, but I eventually got him to send me the high pressure one when I got to the point of being able to actually use it. Ends up costing the same sort of money as the GCG highflow, but this is, of course, the turbo that I KNOW has a shorter length core and so moves the comp cover rearwards. The GCG apparently doesn't do that. My mechanic also swears by the GCG highflow, given that we have another turbo rebuilder who does something essentialy the same as theirs, using Garrett wheels. He says it stands up at really low revs and makes good power. I haven't pushed my HG highflow past ~240-250rwkW yet (should have a little more in it, but unclear how much) and it does have a fairly gentle boost ramp. OK, it's much better now that I have gotten my boost controller tuned up on it.  A lot of my earlier unhappiness was because I couldn't keep the wastegate flap as closed as it needed to be (including some mechanical issues). I'd still prefer it to boost up nearly as quickly as the stocker, and it certainly a bit slower than that. So maybe the GCG one is worth the first look (for you).
    • Ok thanks 🙂 I will higly consider this. Any "known" company for a good reviews and experience to send that off? Is that CJ-motor good one? Or go straight to GCG site? I need to use VPN to even find some of those "shops" let alone access them 🙂 
    • You can literally put in as much WMI as it takes to quench the combustion totally (and then back it off a little, obviously), and it will keep making more and more power. The power comes from the cooling effect of the water (and the meth) and the extra fuel (the meth, which also has massive octane). It is effectively exactly like running E85. One might be slightly better than the other, but they are damn close. But with either you can lean on the boost or the timing (or both) waaaay more than with just petrol and the results are similar. Here's the first thing I googled for an anecdotal bit of evidence. Can't access the attachment without being a gold member, but it is there for the getting if able to, or searched up elsewise perhaps. https://www.hpacademy.com/forum/general-tuning-discussion/show/wmi-vs-e85/
×
×
  • Create New...