Jump to content
SAU Community

Recommended Posts

Hi everyone,

Ive been reading several threads and keep coming across the same problem for alot of different people being wheelspin. Not sure if guys that are new to drag racing are aware of the street radial and the advantages of using them. Im going to do a little experiment next wednesday night with Mona's car.

Compare this weeks sixty foot times on a street tyre to next week on Mickey Thompson Street Radials.

Ill post results on wednesday night. All going well we should be able to organise a group buy for those who are interested. If we oreder 5 or more sets, shold be abel to save $40 a tyre. Usually retail for $290 each.

Ok guys, got some pricing.

235/60/15 $235.00ea

255/50/16 $250.00ea

275/40/17 $275.00ea

This is depending on the amount we buy, im buying one set of each for the shop so we need at least 7 more buyers. these are as cheap as youll find, these tyres retail usually for $270, $290 & $317ea.

Am going to WSID weather permitting on wednesday night so Mona can try a set for a comparison. Will post results, after that ill be ready to order. Can PM me if interested, and will arrange electronic payment.

i can bring tyres to WSID the following week or pick them up from shop.

Link to comment
https://www.sau.com.au/forums/topic/109970-street-radials/
Share on other sites

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Ooooo!!!!! :P so i'm an experiment!!!! LOL!!! hope i don't disappoint! :D

And will definitely be keen on getting some of these tyres if all goes well ;)

Quietly confident that we will see an improvement. Dont worry, no pressure Ha Ha. The tyres will do the work.

Link to comment
https://www.sau.com.au/forums/topic/109970-street-radials/#findComment-2027136
Share on other sites

250 for 16's or 17's??

Moanie how much power is your 33 putting out?

1/4mile time?

engine specs also keen to know

$250 each for 255/50/16, can only get them this cheap if we get 5 or more buyers.

Edited by Bezerkly
Link to comment
https://www.sau.com.au/forums/topic/109970-street-radials/#findComment-2029217
Share on other sites

I am up for a pair of 275/40/17's

:( cheers :(

If we get enough buyers, ill see what we can get a set for, may not be as cheap as the smaller tyres, but still should be discounted.

Link to comment
https://www.sau.com.au/forums/topic/109970-street-radials/#findComment-2029220
Share on other sites

250 for 16's or 17's??

Moanie how much power is your 33 putting out?

1/4mile time?

engine specs also keen to know

The only tyre that comes in a 17 is a 275/40/17. big tyre,

Link to comment
https://www.sau.com.au/forums/topic/109970-street-radials/#findComment-2029225
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...