Jump to content
SAU Community

Recommended Posts

yes a stock GTR is around 180 - 200kw on most dynos. a few kw more with exhaust etc.

i would go.

boost controller (run 1 bar boost)

apexi pods in a custom box

3 inch cat back exhaust

front pipes

dump pipes

Power FC

cam gears (both inlet and exhaust)

and you will get around 240-260rwkw if everything is working properly

i would also do your brakes (new pads, rotors, fluid) and add an oil cooler.

Just got a 90 model GTR?

The first mod you should be doing is a major service.

True, at least all fluids, tyres (if you imported it) and a check over and clean.

After that, drive it around for about 2 months to see if you can 'feel' anything wrong with it before modding.

Also, I got mine dynoed before I did anything to see what the power and boost curves looked like and see if they held steady or spiked/dropped off.

Just got a 90 model GTR?

The first mod you should be doing is a major service.

This goes without saying (but ill say it anyway), change all the fluids - you dont know when they were last changed......if at all.....

i just got a R32 GTR as well, leaving it stock for the moment just to see if there is anything wrong. Don't wanna spend all the cash modding then if something goes bang, your in trouble. Unless money is no issue :P

I've put in a set of XENONs though, but it doesn't go any quicker :D

Edited by gexenon

Just keep the boost at no more than 15psi with the other things mentioned above and you should be fine

And yes, that power (260) will happen with the mods mentioned above, unless theres a problem with your engine

yes a stock GTR is around 180 - 200kw on most dynos. a few kw more with exhaust etc.

i would go.

boost controller (run 1 bar boost)

apexi pods in a custom box3 inch cat back exhaust

front pipes

dump pipes

Power FC

cam gears (both inlet and exhaust)

and you will get around 240-260rwkw if everything is working properly

i would also do your brakes (new pads, rotors, fluid) and add an oil cooler.

Mine has all that less those couple of things and does over 250rwkw. Also need rising rate fuel reg. Plus for that boost level steel wheeled turbos is a handy insurance. I lost a good engine to a blown ceramic turbine as the crap often gets forced into the cylinder causing nasty damage.

Additional to all other suggestions I recommend the timing belt/pulley bearings be replaced ASAP as well as new grade 8 bolts for the bearings.

  • 5 weeks later...
sweet got more replies than i thought

im definatly doing the full fluids change and i was planning to wait a while before trying to get more hp

another question for yas

can my 32 get 240 -260 and still last a while or is it prone to go bang????

I can only tell you of where i went

100K service, doesnt matter if its got 98K or 50K on the clock, you will have a sound base to work from

Redline fluids

Brake fluid

3inch exhaust

front pipe

power fc

boost controller (1 bar)

Adjustable cam gears (both)

= 250rwkw

+ some drag racing

= "hey whats with all the smoke and where is all the power!" (Damn ceramic wheels!)

IMHO Whatever you do be realistic about your expectations and consider the risks.

I dont know your circumstances but if you want to start spending cash on it by all means go nuts.

I did; now i'm asking the forum questions about mods on a 300rwkw combo and contemplating the rebuild next year

....but if you dont, get the service, get a new stereo (is that what young ppl are calling them these days?), fix stuff that becomes an issue

and enjoy driving it for a while...After all it's a still a GTR

Edited by Mr. Keets

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...