Jump to content
SAU Community

Recommended Posts

Im looking at putting a r32 gtr fuel pump into my r32 gtst, Ive read that the pump goes in without any modification, but what about the loom, does it have to be modified at all??Is the standard fuel pressure regulator ok with the gtr fuel pump as ive been advised to get an adjustable regulator???

Any advice or tips would be very much appreciated

Cheers

Link to comment
https://www.sau.com.au/forums/topic/112583-gtr-fuel-pump-into-gtst/
Share on other sites

standard reg will be fine.. as long as its in good condition.

loom is different.. a bit of chop and solder will fix that. Its pretty simple.

Which wires need to be cut and rejoined???Any chance you or someone else has some pictures, they would help me out heaps.

Cheers

How many years is a fuel pump good for? You could be putting a 17 year old fuel pump in a 14year old car???

My cars 17years old anyway (its a 1989 gtst), so its not like im putting a older pump in a newer car, im going for the gtr fuel pump because of ease of fitment, i dont want to be mucking around with aftermarket pumps (changing wiring,lines and mounting it) so the gtr pump seems to be the easiest solution,and quite cheap to at $250 N.Z :)

Edited by nizmo_freek

If a workshop told you that you require an adjustable reg with the GTR pump... dont go there again.

Stock fuel reg is fine. You just need to make sure you have good voltage going to the pump.

Read the DIY section (5 or so section below this) it has a pump install guide for the bosch, the voltage part will be the same :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...