Jump to content
SAU Community

Recommended Posts

I have been advised by the WRX Club Secretary that they need to provide Sandown with a list of names of people who will be officiating or spectating at Sandown on Anzac Day.

You might remember last year that they closed the gates and stopped etting people in. Well this year, if you are not on the list, you dont get entry!!!!

So if anyone is planning on going down to spectate/officiate, you need to email [email protected] and register the following -

Your Name / SAU member number ___.

All entrants will be included automatically.

Anyone who is not a member of SAU, but would like to come down to spectate needs to advise - Your Name / SAU / Guest of <insert drivers name here>

Get your names in fast if you are wanting to come down as there will be limits on how many people they can let through the gate.

Cheers,

Bec

Also - remember is you want to do some flagging (best view points if you ask me) you can email James at [email protected] and he can organise with the WRX club for you.

Anyone who is not a member of SAU, but would like to come down to spectate needs to advise - Your Name / SAU / Guest of <insert drivers name here>

I wont be any1's guest, all i wanna do is spectate with a mate so what do i put down?

and will there be heaps of people going?

Bec, I believe the WRX club are sending a reply email to the ppl requesting to be spectators to verify the SAU or WRX club membership number of the driver they are claiming to be a guest of... so it's not that easy hehe. :D

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...