Jump to content
SAU Community

Cheap Cooler Kits

NO_RSPECT

By NO_RSPECT,
in Western Australia

 Share

Recommended Posts

NO_RSPECT Mentor

NO_RSPECT

Posted
Posted

hey guys hopefully this isnt a double post... but anyone looking for cheap coolers there is an offer on Antilag in the for sale section

I just picked up a kit today.. it all looks in order..

piping/hoses/clamps/cooler $400

just wanted to put it out there incase anyone was planning on getting one

Link to comment
https://www.sau.com.au/forums/topic/113671-cheap-cooler-kits/
Share on other sites
NO_RSPECT Mentor

NO_RSPECT

Posted
  • Author
Posted

go to antilags for sale section.... says there are kits for 32, 33 and 34...

most ppl here got 32's and 33's anyways..

when i fit one to a 34 i will let you know if its any good..

don't suspect any dramas

noise...you had any problems specifically.?

only thing i know of is the bracket attached to bolt to the block, needs to be modified a little to bolt up...even then, it doesnt really even need to be bolted once its all joined.. thats all i know of.. if you know of something else.. enlighten.. before too many people rush out

noise Mentor

noise

Posted
Posted (edited)

r34 has the washer bottle in the way and different distances to things. I came down to the workshop with my car pulled apart and he showed me all the parts not lining up.

He also told me he has seen plenty of kits that just dont fit, saying that, some must fit or there wouldnt be a market for them.

This is all from a "reputable" if there are any, workshop in perth.

The china kit i bought came with instructions and pictures for an r33 even though it was sold for "r34". The instructions included bending the chasis slightly and didnt say what to do about the water bottle.

I ended up returning the kit and getting a full custom stainless steel install.

full custom stainless installed is only a few hundred more then china kit installed, if you pay a workshop.

just a warning from my experience :)

Edited by noise
NO_RSPECT Mentor

NO_RSPECT

Posted
  • Author
Posted

oh yeah the washer bottle, i read that on satanics website.NSW member.

i hope it at least semi fits.. shouldn't be a big issue either way.. i did stainless piping on the satria conversion and that was fairly straight forward.

:(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...