Jump to content
SAU Community

Recommended Posts

Does anyone know of anyone that specialises in fixing th gauges on the dash board?

Last night, notice my speedo is out by approximately 5k according to the avc-r.

the fuel gauge is also WAY WAY out. It's showing it has more fuel in the car when really it doesnt have what it says in it.

Wanting to get this done on Saturday, so anyone know of any, would be great.

Link to comment
https://www.sau.com.au/forums/topic/114229-guage-specialist/
Share on other sites

Have you got aftermarket rims?

Noticed my speedo is slightly out vs the PFC, I'm guessing that this is resulting from actual output from the vehicle speed sensors and also from change in rolling diameter(can be out by a significant amount depending on the size you get).

Your fuel reading: Open up your fuel tank and check the fuel level sender thing (big long piece of plastic). It's supposed to be supported on a bracket and if it has come off then it won't give a correct reading. ie - I don't think this is an instrumentation problem.

all this was working perfectly fine before the white dials were installed.

i know its the needles that are out of place for sure!

dan's going to look at this again tomorrow though.

did you do the dials? if you did then you will know what i'm talking about. you would of put the needles back in the wrong place to fix them it will take some time you will have to take it out again take off the clear cover put it back in start your car and put the needle back on the 0 km's per hour with the fuel full your car then put the needle on full. should work.

lol i was in my mates car the other day, and noticed his tacho on the dash, the needle sits on the highest point and when he revs it gets lower, ie idle on 6500 and when flooring it is at 3000 etc i found it so ammusing.. lol

all this was working perfectly fine before the white dials were installed.

i know its the needles that are out of place for sure!

dan's going to look at this again tomorrow though.

ABLE INSTRUMENTS: ph 3801 1232. They are at Loganholme. These guys are pretty good. I even used them to shorten the speedo drive cable on my R32 when I installed the RB25 gearbox.

since having the white dials put in and having the needles read correctly has been a bit of a mission since then. hence why these 2 are out by a bit.

if you have ever physically moved your speedo needle with your finger or something, its pretty much f**ked

I learnt from experience :miner:

ABLE INSTRUMENTS: ph 3801 1232. They are at Loganholme. These guys are pretty good. I even used them to shorten the speedo drive cable on my R32 when I installed the RB25 gearbox.

Can you remember the cost??? I know how much my speedo is out, but if it didnt cost much it might be worth it.

At the dyno night im gonna get them to see how close 100kph is on my dial as to what the dyno says...

This is the best way to tell how well your spedo is calibrated...

As compaired to other cars i mean... Cause whos to say the dyno is right?

you could always just wait til I fix it and all will be ok.

Like I said to you, the fuel guage was the only drama because I set it up on under half a tank. All that needs to be done is fill it up and re-set it. As for the speedo, wait til you get it on the dyno and then tell me how far out it is.

When I was a surveyors assitant doing road condition surveys we had to recalibrate the speedo every day due to tyre wear, I was surprised how much it was out each time. This is an extreme case I know but it just showed me how inaccurate car speedos are (we had an an electronic jobby in the test vehicle), we tested it on a stretch of road that had 1km marked on it and at the start point I had to spray the mark on the tyre and at the 1km mark the computer would tell us where the mark should be and then compare to where it actually was.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...