Jump to content
SAU Community

Recommended Posts

  • Replies 240
  • Created
  • Last Reply

Top Posters In This Topic

It so is

Look, a 34 gtr will cost you $60k

Keeping your car will mean the following expenses:

GTR 34 seats $2000

GTR wheels $2500

GTR motor $7000

AWD system $1500

GTR body kit $4000

GTR front and rear diffusers $1500

GTR Rear wing $500

GTR MFD $1000

GTR steering wheel $250

GTR trim $1000

GTR badges $150

GTR Xenons $4000

The fact that you will have a 3 year newer car = $10k

So there you go. Theres your 55-60k worth :)

It so is

Look, a 34 gtr will cost you $60k

Keeping your car will mean the following expenses:

GTR 34 seats $2000

GTR wheels $2500

GTR motor $7000

AWD system $1500

GTR body kit $4000

GTR front and rear diffusers $1500

GTR Rear wing $500

GTR MFD $1000

GTR steering wheel $250

GTR trim $1000

GTR badges $150

GTR Xenons $4000

The fact that you will have a 3 year newer car = $10k

So there you go. Theres your 55-60k worth :)

Where do you get a rear c/f defuser for a 34 GTR for anywhere near $1500?

Go the RB 30 dett mona

It so is

Look, a 34 gtr will cost you $60k

Keeping your car will mean the following expenses:

GTR 34 seats $2000

GTR wheels $2500

GTR motor $7000

AWD system $1500

GTR body kit $4000

GTR front and rear diffusers $1500

GTR Rear wing $500

GTR MFD $1000

GTR steering wheel $250

GTR trim $1000

GTR badges $150

GTR Xenons $4000

The fact that you will have a 3 year newer car = $10k

So there you go. Theres your 55-60k worth :D

Dont prove me wrong guys. I Wont hear a word of it :dry:

I need a smiley to express the fact that I am SO tempted to say something but am biting my tongue because I cbf arguing with some people. :)

Edit - that quote from R32R at the top of the page is wrong, very very wrong. I think he's got things crossed up.

Sif.

Bring it, Bish.

I stand by what I said.

3L bottom ends help ONLY with low end torque/tractability (good for general street use, yes)

BUT

The shorter stroke RB26 based engines are ALWAYS a better idea as out-and-out race engines, for all the reasons I mentioned and more.

Need I remind you that the 3 fastest drag GT-Rs on the planet use 2.8L or smaller engines, with the HKS 33 using their own 2.8L kit (crank has 4mm more stroke than normal [77.7mm])

But I'm sure in your mind the 3/3.1L jobbies are better, right?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...