Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

is it once a month for the whole year. also if i attend to these do i have to bring a helmet or anything else?? and is it always on a friday??

yes its normal once a month, and yes the practises are always on the friday..

you will need a Helment, long sleave top, pants and closes shoes..

remember you need to apply for WASCC $300 and Cams (Lvl2 speed or non-speed) $50

and these are yearly fees.. you can not drift without a WASCC membership and cams lvl2 or higher

also if you do come... be perpared to have only about 4-6 goes (at 4laps per go)... also if you dont know what ur doing dont try anything crazy as u will end up in the sand...

its good fun but there is a chance u can bin ur car pretty easy if u try something above ur lvl or grab some under under

Link to comment
https://www.sau.com.au/forums/topic/114832-drifting/page/3/#findComment-2302827
Share on other sites

can i rock up any time between 6.30-10.30, cause i dont finish work intill 7-8ish

no point if its that late

the practise starts at 6:30 and as soon as they have 40cars, they close it off..

practises finish around 10, so the later you get there the less runs you will get

Link to comment
https://www.sau.com.au/forums/topic/114832-drifting/page/3/#findComment-2302953
Share on other sites

is it possible to just go there and watch? coz i dont have the budget to join the membership for barbagallo and the lvl2 CAM license >.< i went to the track before and got a good look at it as it is quite close to my house(10-15 mins drive) im stayin in joondalup. im not too sure if im willin to risk my car to drift coz if i have any dmg its gonna cost me a bomb :)

Link to comment
https://www.sau.com.au/forums/topic/114832-drifting/page/3/#findComment-2304726
Share on other sites

is it possible to just go there and watch? coz i dont have the budget to join the membership for barbagallo and the lvl2 CAM license >.< i went to the track before and got a good look at it as it is quite close to my house(10-15 mins drive) im stayin in joondalup. im not too sure if im willin to risk my car to drift coz if i have any dmg its gonna cost me a bomb :)

yeap you can go to watch,

practise are starting to get very good by this i mean the general skill level of everyone has increase a bucket load... so you get to see some awsome drifting

Link to comment
https://www.sau.com.au/forums/topic/114832-drifting/page/3/#findComment-2304794
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...