Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

8000rpm and side step the clutch, hangon, grab 2nd, hangon again, don't forget their is a hairpin at the end of the straight :D

Haha, I'll keep the hairpin in mind. :) What rpm do you usually launch at?

Be nice to 3rd tho.

3rd is evil and must be punished!

Ask me to race it ;)

no, no and no. :angry:

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116006
Share on other sites

launching at around 7000 should be plenty. if you need more then try another 500 or so the next time. personally i wouldn't side step the clutch, but just let it out as fast as your foot can move back up off it. will be a bit kinder and you should still get 1.8sec 60ft. i'm no expert though, so probably a good idea not to listen to me!

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116727
Share on other sites

Hey all,

I have spent my fair share of time on the track doing circuits etc but never run the 1/4.

What hints / tips do you guys have for my first run in the GTR tomorrow?

Thanks all,

Christian

Hi Christian, my tips would be:

1. Drive around the water if you dont want to do a burn out.

2. leave you window down a bit and tell the starting guys thats its your 1st time. They will show you where to stop. It's offen hard to see where the line is, and you don't won't to be floundering around reversing and going forward until the staging light go on.

3. Bring your rev's up to about 6500-7000rpm and hold them there. (depends on what power you have and how good your grip is). You dont wont your rev's to be too low or you will bog down off the line).

4. Lift you foot off the clutch until you feel it take, and then wait until the green lights, then lift off all the way, and then launch the thing.

5. 2nd gear change will come very quickly, so try not to bounce it off the limiter too much.

6. change at about 8000rpm.

7. When you go over the finish line keep your foot down all the way over the line. You will probably have to change into 5th going over the line.

8. Don't put your foot anywhere near the brake......just use the gears to slow down. (I've done this and I slid all over the track)

Also.........you don't need to go as soon as you see the green, just take your time. The timer starts when you cross the starting line.

This probably sounds all straight forward. I am a very conservative Drag..er...So, I hope some of the advice sounds ok. :w00t:

Stacey (the smarter and more consistant part of DiRTgarage)

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116924
Share on other sites

Thanks Stacey, that helps a lot. How far is the run off after the line?

Yes , I think it's more than the lenght of the track. You will have plenty of time to slow down. On my 1st go I ended up with my front wheels in the 'sand trap' (it's actually all rocks and gravel), so try and avoid that if you can.

And yes, have fun as it is a really good buzz. Also another bit of advice I tell people is to keep it as simple as you can. I always seem to be consistant with my times becasue I dont have much to worry about or remember to do.......other than launching. Reducing the amount of things you have to switch on/off or spin before hand is a good thing. IMO. :)

Hope it's not raining in Sydney.

Cheers..........Stacey

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117023
Share on other sites

From WSID:

"The WSID facility is a full international standard drag strip, built to current NHRA specifications. The braking are is 600 metres of asphalt, with a 120 metre gravel trap and catch net at the end. The track is 70 metres above sea level at the start line and approximately 66 metres at the finish line."

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117035
Share on other sites

Yes , I think it's more than the lenght of the track. You will have plenty of time to slow down. On my 1st go I ended up with my front wheels in the 'sand trap' (it's actually all rocks and gravel), so try and avoid that if you can.

And yes, have fun as it is a really good buzz. Also another bit of advice I tell people is to keep it as simple as you can. I always seem to be consistant with my times becasue I dont have much to worry about or remember to do.......other than launching. Reducing the amount of things you have to switch on/off or spin before hand is a good thing. IMO. :)

Hope it's not raining in Sydney.

Cheers..........Stacey

Awesome, thanks! :O

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117054
Share on other sites

I was shitting the first time i raced - was at the old ECRaceway main straight. BUT by the time I got into 3rd gear it felt natural and safe.

You'll be right but it's handy to have someone walk out onto the racing surface and show you where to stage so you don't roll through the lights and stage with your back wheels (I did this once @ ECR). Trust me you look like a dick when you do this :)

For some reason they don't let you get a 3/4-GTR lead on the line :O

Don't forget "The Book" either!!!! <----- single most important thing to remember.

Adrian

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117067
Share on other sites

Thanks Adrian, yeah it'll be good to have a chat beforehand as I said, I'm nervous as hell.

Christian

I reckon talking about it anymore than you are will just make you more nervous. Just line up on the line (little white lines either side of your lane), wait for the green light, foot on the throttle and brake once you go past the big digital timing displays. Treat it like a traffic light grand prix and you'll be right.

Most people have trouble just finding the start line (how I have no idea) so dont even try doing a 12sec pass on your first run, just get to the finish line, grab your time slip and line up again.

Edit: I'll be there just after 6pm as always, look for me in the hotdog line :)

Edited by benm
Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117072
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...