Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

8000rpm and side step the clutch, hangon, grab 2nd, hangon again, don't forget their is a hairpin at the end of the straight :D

Haha, I'll keep the hairpin in mind. :) What rpm do you usually launch at?

Be nice to 3rd tho.

3rd is evil and must be punished!

Ask me to race it ;)

no, no and no. :angry:

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116006
Share on other sites

launching at around 7000 should be plenty. if you need more then try another 500 or so the next time. personally i wouldn't side step the clutch, but just let it out as fast as your foot can move back up off it. will be a bit kinder and you should still get 1.8sec 60ft. i'm no expert though, so probably a good idea not to listen to me!

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116727
Share on other sites

Hey all,

I have spent my fair share of time on the track doing circuits etc but never run the 1/4.

What hints / tips do you guys have for my first run in the GTR tomorrow?

Thanks all,

Christian

Hi Christian, my tips would be:

1. Drive around the water if you dont want to do a burn out.

2. leave you window down a bit and tell the starting guys thats its your 1st time. They will show you where to stop. It's offen hard to see where the line is, and you don't won't to be floundering around reversing and going forward until the staging light go on.

3. Bring your rev's up to about 6500-7000rpm and hold them there. (depends on what power you have and how good your grip is). You dont wont your rev's to be too low or you will bog down off the line).

4. Lift you foot off the clutch until you feel it take, and then wait until the green lights, then lift off all the way, and then launch the thing.

5. 2nd gear change will come very quickly, so try not to bounce it off the limiter too much.

6. change at about 8000rpm.

7. When you go over the finish line keep your foot down all the way over the line. You will probably have to change into 5th going over the line.

8. Don't put your foot anywhere near the brake......just use the gears to slow down. (I've done this and I slid all over the track)

Also.........you don't need to go as soon as you see the green, just take your time. The timer starts when you cross the starting line.

This probably sounds all straight forward. I am a very conservative Drag..er...So, I hope some of the advice sounds ok. :w00t:

Stacey (the smarter and more consistant part of DiRTgarage)

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2116924
Share on other sites

Thanks Stacey, that helps a lot. How far is the run off after the line?

Yes , I think it's more than the lenght of the track. You will have plenty of time to slow down. On my 1st go I ended up with my front wheels in the 'sand trap' (it's actually all rocks and gravel), so try and avoid that if you can.

And yes, have fun as it is a really good buzz. Also another bit of advice I tell people is to keep it as simple as you can. I always seem to be consistant with my times becasue I dont have much to worry about or remember to do.......other than launching. Reducing the amount of things you have to switch on/off or spin before hand is a good thing. IMO. :)

Hope it's not raining in Sydney.

Cheers..........Stacey

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117023
Share on other sites

From WSID:

"The WSID facility is a full international standard drag strip, built to current NHRA specifications. The braking are is 600 metres of asphalt, with a 120 metre gravel trap and catch net at the end. The track is 70 metres above sea level at the start line and approximately 66 metres at the finish line."

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117035
Share on other sites

Yes , I think it's more than the lenght of the track. You will have plenty of time to slow down. On my 1st go I ended up with my front wheels in the 'sand trap' (it's actually all rocks and gravel), so try and avoid that if you can.

And yes, have fun as it is a really good buzz. Also another bit of advice I tell people is to keep it as simple as you can. I always seem to be consistant with my times becasue I dont have much to worry about or remember to do.......other than launching. Reducing the amount of things you have to switch on/off or spin before hand is a good thing. IMO. :)

Hope it's not raining in Sydney.

Cheers..........Stacey

Awesome, thanks! :O

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117054
Share on other sites

I was shitting the first time i raced - was at the old ECRaceway main straight. BUT by the time I got into 3rd gear it felt natural and safe.

You'll be right but it's handy to have someone walk out onto the racing surface and show you where to stage so you don't roll through the lights and stage with your back wheels (I did this once @ ECR). Trust me you look like a dick when you do this :)

For some reason they don't let you get a 3/4-GTR lead on the line :O

Don't forget "The Book" either!!!! <----- single most important thing to remember.

Adrian

Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117067
Share on other sites

Thanks Adrian, yeah it'll be good to have a chat beforehand as I said, I'm nervous as hell.

Christian

I reckon talking about it anymore than you are will just make you more nervous. Just line up on the line (little white lines either side of your lane), wait for the green light, foot on the throttle and brake once you go past the big digital timing displays. Treat it like a traffic light grand prix and you'll be right.

Most people have trouble just finding the start line (how I have no idea) so dont even try doing a 12sec pass on your first run, just get to the finish line, grab your time slip and line up again.

Edit: I'll be there just after 6pm as always, look for me in the hotdog line :)

Edited by benm
Link to comment
https://www.sau.com.au/forums/topic/114913-new-drager/#findComment-2117072
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...