Jump to content
SAU Community

Recommended Posts

Hey guys i just bought a R32 GTST and interms of engine mods it has a 3inch turbo back exhaust, a Cold Air Intake, a 500hp Boch fuel pump and a BOV. These mods were already on the car so i was wondering what the nxt step would be interms of reachin 180rwkw...... :angry:

could anyone tell me what coil packs do and if they would give ma a bit of power and yeh what the nxt steps i shoudl be takin were...oh and by the way im not prepared ot buy a bigger turbo or a another ecu atm so yeh jus pov mods at the moment lol :D

thanks

Daniel

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/
Share on other sites

hi mate congrats on the purchase, all i can think of is a front mount and a boost control i'm in the same boat not prepared on getting a bigger turbo just yet, my line is pretty much same as your as mods go apart from fuel pump, not so sure bout the coil packs i'd ho;d back on them until you upgrade your turbo, i'm planning on getting a adjustable fuel pressure regulater and a bosch 044 fuel pump soon and i think that will do me for awhile until i saved enough for bigger turbo,

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/#findComment-2116177
Share on other sites

you sure your gonna require a 044?

thats pretty big, and damn noisy, oh and external aswell.

have a run through here

http://www.skylinesaustralia.com/forums/in...howtopic=103095

see what they have and how much power they got.

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/#findComment-2116179
Share on other sites

congrats on teh purchase!

- firstly give it a service: oil, oil filter, coolant, spark plugs, fuel filter, oxygen sensor

- then, put it on the dyno for an hour and get the tuner to see how healthy the engine is. they can also play around with your timing to get the most out of what you have got. plus you will get a power figure to see what the car is making

What are coil packs you ask?

they are coils within a little plastic pack that sit over the spark plugs. there's one over each spark plug. they generate a signal when instructed to do so, and pass this to the spark plug which creates a spark to ignite the fuel.

Will putting bigger coils generate more power?

Well it will generate a bigger spark, but this probably won't equate into much more power unfortunately

if you want to play around with the car a little more, i would suggest thinging of some of the following:

- front-mount intercooler ($300) and piping ($400)

- boost controller ($50) set to about 12psi (any more then 14psi can cause the turbo to fail)

That will give you a nice jump in power. they generally say 1psi raises power by 10kw when in the right setting (ie already have exhaust and intercooler)

good luck!

Warren.

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/#findComment-2116202
Share on other sites

Will putting bigger coils generate more power?

Well it will generate a bigger spark, but this probably won't equate into much more power unfortunately

will only give a power increase if the current coils are not working.

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/#findComment-2116258
Share on other sites

Next step is a fmic, and unfortuately thats the end of the pov mods. Turbo, injectors and ecu are next.

You will need a turbo to make 180 as the stocker doesn't like to play much past 160 odd. An rb25 turbo will do it though and they are cheap enough.

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/#findComment-2116555
Share on other sites

fmic and 14psi boost should see close to 165-170rwkw if you are willing to test that sort of boost on stock turbo..

a few people have..

i think both roy and cubes ran this sort of boost on stock turbo and it didn't break..

no guarantees though..

180rwkw is not going to happen with stock turbo.

fmic kit from JUST JAP will set you back $500 or so.. see traders for sale section.

Dr Drift can also do retuned Stock ECU for about $400 or so I think.

now.. you say you don't want to change turbo but considering an Rb25 turbo will cost you like $350 these days, it's cheaper than both the above bits, but they are ALL needed for the 180rwkw you are after.

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/#findComment-2116586
Share on other sites

thanks heaps...i do have a boost controller (sorry forgot to mention) i boosted to abotu 15psi and started to shyt myself abit so i turned it down to about 10 lol so i decided to do what u guys said and look at a 33 turbo and yeh its onlly about 300 bux anyone know about how mani kws u can get out of it and how much boost it can handle ?

And as for the front mount ive been looking and alot of them, theres heaps of copy ones out there and they all claim to do the same as the hybrid ones but like yeh not too sure about that ;) Im thinkin i should just hold out for a lil while, not settle of crap, go for quality and buy the Hybrid 600mm yeh ?

cheers

oh and i knwo this isnt the place to post it but im afta a new steerin wheel so if ne1 got one and lives in melb let me know...cheers ( again sorry about postin this in here)

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/#findComment-2117990
Share on other sites

hybrid copies are fine.

they are all the same except that HYBRID have plastered their name on the core.. it's the same core as the non marked ones, and comes from the same factory.

it'll do the job and do it well.

r33 turbo will make around 170-190 rwkw on about 13-14psi on an RB20 depending on dyno.

Link to comment
https://www.sau.com.au/forums/topic/114929-r32/#findComment-2118076
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...