Jump to content
SAU Community

Recommended Posts

Well well well, I can here the "cha ching" of the cash register from here....looks like Universal have figured a way to sqeeze more money out of Vin and the gang. Considering this movie has nothing at all to do with the last two, nor does it have any cast from the previous two I'd say it's a fair bet it will....SUCK BALLS! About the only good thing I saw in the trailer were the women and the well known Signal R34. Does look like the write off a few of them though! More ricey rockets with Motec exhaust systems and floor pans that drop out when you nawwwwwsss too much.....I can't wait....no really...

Plot - From the producer of the worldwide blockbuster hits "The Fast and the Furious" and its sequel, "2 Fast 2 Furious," comes the latest installment of the adrenaline-inducing series built on speed-"The Fast and the Furious: Tokyo Drift". Set in the sexy and colorful underground world of Japanese drift racing, the newest and fastest customized rides go head-to-head on some of the most perilous courses in the world.

Sean Boswell (Black) is an outsider who attempts to define himself as a hot-headed, underdog street racer. Although racing provides a temporary escape from an unhappy home and the superficial world around him, it has also made Sean unpopular with the local authorities. To avoid jail time, Sean is sent to live with his gruff, estranged father, a career military-man stationed in Tokyo.

Now officially a gaijin (outsider), Sean feels even more shut out in a land of foreign customs and codes of honor. But it doesn't take long for him to find some action when a fellow American buddy, Twinkie (Bow Wow), introduces him to the underground world of drift racing. Sean's simple drag racing gets replaced by a rubber-burning, automotive art form-with an exhilarating balance of speeding and gliding through a heart-stopping course of hairpin turns and switchbacks.

On his first time out drifting, Sean unknowingly takes on D.K., the "Drift King," a local champ with ties to the Japanese crime machine Yakuza. Sean's loss comes at a high price tag when he's forced to work off the debt under the thumb of ex-pat, Han (Kang). Han soon welcomes Sean into this family of misfits and introduces him to the real principles of drifting. But when Sean falls for D.K.'s girlfriend, Neela (newcomer Kelley), an explosive series of events is set into motion, climaxing with an ultimate high stakes face off.

Adz rating 1.5\10.....and I havn't even seen it! :ban:

post-2471-1146108008.jpg

post-2471-1146108027.jpg

post-2471-1146108052.jpg

lil bow wow.. hahaha

From DEM FRANCHIZE BOYZ: I think they like me (feat bow wow)

[bow Wow:]

"Im bow weezy prince of the o-town

Just got the wheels clean so im riding slow now

Im in a fast car something like a nascar

If you wanna know how much it cost you should ask pa"

lol

PS so whens the NissanSilvia movie meet? :ban:

if thats the case then why dont you ask these nice people to back off the line so you can go home...

all jokes aside, who here has NOT seen number 1 or 2....as weak and cheesy as they are, people watch them and they make squillions. this 1 will be even lamer than the first 2 by the look of it, but it'll be just as successful I think...and the majority of people on SAU will watch it :ban:

Hello Victorians,

I'm treading carefully on these grounds haha.

I would go see just for the cars. The plot seems a little "hollywood".

Can you imagine the hooning that would follow the movie in the car parks? I remember when F&F came out, it was boosting galore here in Brisbane.

yeah but anyone can blame movies and video games for wankers thinking there in it.

like omg lets ban violent video games coz my son stabbed some other kid. its the video games fault, not my poor parenting thats to blame.

bah.

Hello Victorians,

I'm treading carefully on these grounds haha.

I would go see just for the cars. The plot seems a little "hollywood".

Can you imagine the hooning that would follow the movie in the car parks? I remember when F&F came out, it was boosting galore here in Brisbane.

Yeah, isn't it what made the 34's so ace in the first place? I'm gonna be lapping up the attention from those hot 7-12 year olds....oh hang on.... :P

this plot sounds a bit like the one from The legend of speed i think it was called. It was a japanese movie but i think that it was good because the cars weren't riced up. In fact no stickers at all.

No Vin & no Paul Walker - whats the point of even going??? :)

http://movies.yahoo.com/movie/1808715999/trailer

I can see two 6 packs and a few scotches as a pre-requisite to see this movie...i can also see plenty of reasons in short skirts to see it....but i fear that this movie will be so bad that not even the booz and tale can hide my disgust

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...