Jump to content
SAU Community

Recommended Posts

WGMG MY NEIGHBOURS...after they mow the lawn, they get out the blower and start revving the shit out of it, as if it was a motor bike, then proceed to make sure not one leaf is on the lawn... this is loud and annoying and every friggen weekend just about... THEN, he starts his POS motor bike and revs that a few times on cold start... AND whats topped me off today is when Hodgie159 pulled up in the drive way, these fat f*kers yell out *TURN THAT FKN THING OFF*.... it was 10am FFS..not like it was 7am on a sunday... I was speechless... so I told him to give it a bit as he left :D just to piss them off some more!!.... And the last word from the house across the road was *FK Head*... nice neighbours. Just Karma biting you on the arse for all the noise you make!.. Oh and they are the noisest neighbours in our street !!!

Seriously, where to people get off these days..

i think we should have a SAU Meet up at 6am at your place StageaGirl..haha show them how it feels..lol

And tell everyone there, to rev their engines at the same time infront of their house XD.

Haha I get everyone to set their turbo timers for 10 mins and then walk away haha

WGMG some dickheads smashing my window on my car and stealing my camera . . . cant leave cars anywhere anymore

Nothing says goodmorning like a limestone rock and sashed glass all in my car

Cops following you!!

And Double Demerits. I'm a P-plater, so if I lose 4 demerits at one time I lose my license. Least amount of demerits you can lose at one time is 2. Double that makes it 4. Therefore you your license. And with all the cops and cameras around, its getting harder!!

And having $10 in your account and no fuel in your tank. I dont get paid til Thursday :blink:




  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...