Jump to content
SAU Community

Recommended Posts

Okay, i went to the NGK website and found the part numbers for the o2 sensors that should go in my R32 GTR, but i have rung around and no-one has them in stock, they are NGK-OTD2F-P1P, but then i went searching and found that the nissan silvia SR20DET engine uses the same plug...but to add to that, i went to but some o2 sensors for a SR20DET and the dude is telling me the part number is NGK-OZA395-E2. will these work or do they need to be the OTD2F-P1P sensors? and where can i get them from if anyone knows :S thanks...

Link to comment
https://www.sau.com.au/forums/topic/116364-gtr-oxygen-sensors/
Share on other sites

Me? I have a set for sale R32 GTR :P

http://www.skylinesaustralia.com/forums/in...opic=115107&hl=

There are two part codes for GTR sensors are they are different connectors on each sensor (front to rear)

Nissan is where everyone gets them from as far as i understand... although they want $420+

You didn't search very well :P

http://www.pcug.org.au/~jdeakins/facts.html

PM "GTaaargh" and ask if he has the NGK part numbers (and a source) for the front and rear as he has been in touch with a tech at NGK.

Otherwise, now is a good time to become an SAU member and take advantage of discounted Nissan parts. Or buy Ash's O2 sensors.

ford el falcon series happens to suit R33 GTST only.

it just happens to be in same voltage scale and range.

If you ask for a ford el falcon oxygen sensor you get an OEM generic brand oxygen sensor and it just happens it fits the R33 dump and voltage matches

if your trying to improve fuel economy I have looked into this too.

Most people i have spoken to get 300-350kms per tank around town so in my case thats what I'm getting, so I am going to save my money in the o2 sensor departmant.

I wish I could get better than that!

good luck.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...