Jump to content
SAU Community

Recommended Posts

Well i'll be running an rb25 pfc in my rb24det using the rb20 loom and sensors in the next week, from what i can see of the wiring diagrams carl h is correct. should just bump and run.

when using one of these does all the options show correctly on the power fc controller?

i also was under the impression the series 2 ran different coils, the power fc's have the same part number so is that more wiring related?

in respect to the gtr power fc, from what i also understand it runs exactly the same pin out however the afm's need to be run in parallel and likewise with the oxy sensors. is this correct?

when we tried this on my buddies car it booted up fine and started right away, put it into the monitior mode and it displayed everything that would normaly be displayed on the rb25pfc.

played around with it and to check that the car was indeed running right lowered the revlimit to 1.5k and low and behold it cut at 1.5.

I think the RB25 PFC is a better bet for an RB20 than the GTR model, reason being that the RB20/25 share the same type of knock sensor (resonant) and the RB26 uses a flat response (non resonant) sensor.

The RB25 PFC is designed to work with the type of knock sensor that the RB20 has.

hey mate heres the pinouts for r32 rb26 ecu

rb26 ecu pinouts

are you sure this is correct? these pin outs are almost the same as the rb25 sheet here (incl the injector grounds which are different)

if you check the loom on rb20det.com you will see there is a difference between the rb20/20 det and i was always under the impression the r32 rb series had the same loom

POST EDITED

Loom is correct. I have the manual for ca18,rb20de,det,rb25de,rb26dett (r32) and it looks like that changing to a rb26 power fc you also need to swap 112 & 114 pins around + the rewiring of the afms etc

Edited by SirRacer

Using an rb26dett loom on an rb25de (r33 head) the differences are

Differences

* Wastegate valve control solonoid (dont see why u wont need it anyway)

* AFM Ground (wire afm in parallel and would be fine or dejetro)

* AFM Intake sensor front (depending on what one you use you could run 2 or wire as above, i think the 26 expects a different air temp sensor though)

* Intake air temp sensor

* Throttle valve switch (dont have a clue what this is but affects r32 also)

* Fuel pump terminal control output 1

* Fuel pump terminal control output 2

* Sub electrical fan relay

r32 rb25de(Loom is basically same as rb20det, however rb20 has a fuel control terminal volt control output and FICD solenoid input signal.

rb20/25de (r32) with r33 rb25 computer

Differences

* FICD solenoid input signal (not used by r33 computer or rb20det loom)

* Swapping of injectors to suit loom 112 & 114

* Throttle valve switch (isnt on r33 loom)

r33 rb25de loom is the same as rb25det

some things we may need to clarify( i think they are for the slushbox) so power fc wont support them anyway

* Throttle sensor output signal (Says to A/T C/U)

* Throttle valve switch power supply

* Intake air output signal (Says to A/T C/U)

* Engine A/T control input signal

Edited by SirRacer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...