Jump to content
SAU Community

Rb20 Motor, Gearbox, Etc; Package

rb20inside
 Share

Recommended Posts

rb20inside Community Regular

rb20inside

Posted
Posted (edited)

for sale:

93 rb20det motor package

approx 75,000kms

includes complete motor, gearbox, flywheel, clutch, manifolds, turbo

also included: r32 crossmember, engine mounts, gearbox mount, tailshaft, radiator

all parts included add up to almost a complete front cut

prefer to sell it all together or if to different buyers most parts at once

reply to pm as i dont check the thread much

located near(west) brisbane

if i cant get a buyer does anyone have/know of a cheap s13 or r32 i could put it all straight in?

other parts on offer include:

*microtech LT8S. incudes hand controller, lume, sensors, etc. sold

*3in dump/front pipe (one piece, bell mouth style not split)

*greddy intercooler (some stone damage as expected) includes piping if you want it. $250

*apexi twin chamber bov. $150ono

*z32 hubs and spindles. $100ono

*gtr injectors. sold

*s2 rb25 turbo. guess you could say its blown. has a bit of shaft play and is a bit noisy/squeals. great for rebuild/hiflow. $200

*s14a complete rear cradle (includes cradle, lsd diff, halfshafts, all control arms etc, hubs/5stud spindles, swaybar, rotors, calipers, handbrake cables, etc. $500

Edited by rb20inside
Link to comment
https://www.sau.com.au/forums/topic/117346-rb20-motor-gearbox-etc-package/
Share on other sites
dbo Enthusiast

dbo

Posted
Posted (edited)

microtech LT8S. incudes hand controller, lume, sensors, etc

Whats this worth? Guessing it was on your RB20?

edit: wait the LT8S is traditionally 4x injector 4x spark.. so this doesn't fit on an RB20?

Edited by dbo
rb20inside Community Regular

rb20inside

Posted
  • Author
Posted (edited)

price is $300 for the gtr injectors. condition is fine although i havn't had them flow tested, they came out of a running gtr and were only pulled out as they were replaced by sard 720cc items.

the microtech came from a running rb20det so is a 6 injector/spark output unit. it includes/sliced into a rb20 wiring lume.

now that you mention it i am unsure as to whether its a lt8s or ltx8s (as its at a mate house, sorry guys but i will find out for sure)

i was under the impression the lt8 and older mtx8 were the 4 output units whereas the lt8s was the 6 cylinder unit. but in saying that i've seen a lt8 used on a r32 gtr.

anyway it works with and came from a rb20

after about $1000

Edited by rb20inside
rb20inside Community Regular

rb20inside

Posted
  • Author
Posted (edited)

have checked. the microtech is definitely a LT8S. it can run a 6cyl/output car

anyone got a cheap (non turbo auto??) s13 they dont want?

Edited by rb20inside
Alainuae Apprentice

Alainuae

Posted
Posted

hey mate you still looking for the cheap silvy? i got one ready for a rb20 to drop in. I was about to do the same myself as i have the RB20DET engine and nearly all the parts even the r32 box ready to just go in but im willing to sell the car as is (old ca18de box aswell ripped out) So its ready for the rb20 to go in.

So let me know how much u are willing to spend if you want it and we might work somehting out.

Cheers

Rob

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Rear subframe stay bracket bolt removal issues

      By GTSBoy · Posted

      Grind them off, drill them out. Repair any rust on the other side. Start again from scratch.
    • Iron Mike
      R34 GTR parts garage clean out

      By Iron Mike · Posted

      Big R34 GTR parts cleanout. I have a lot of stuff collected over the last 14 years and my missus is giving me hard time. Make my life easy.   Nismo GT carbon fibre diffuser fins (discontinued)  NEW  $2900 Garage Defend Stingray canards carbon fibre  NEW  $1300  Top Secret G Force carbon fibre front diffuser  NEW  $2000  Haltech Elite 2500  NEW  $2500  Haltech Platinum Pro R34 GTR   USED  $1400  Apex’I power FC D'jetro + hand controller R34 GTR   USED  $1400  Nissan OEM BNR34 ECU  USED   $1000  HKS EVC 6  USED  $600  Blitz dual SBC ID boost controller.  USED  $350  TRE 255 LPH Fuel pump  NEW  $100  Fujitsubo  Super Ti exhaust  USED  $2700  Tomei Expreme Ti exhaust  USED  $2000  Trust stainless steel front pipe  USED  $1000  Apex’I super suction kit  USED $400  BC BR coilovers  USED  $600  Hardrace front upper camber kit. USED  $300  Garret 2860-5 turbos –  one good, one needs reco USED  $1000  Nissan OEM Toshiba MFD Screen replacement  NEW  $450  Nissan OEM BNR34 Series II front passenger seat  USED (mint) $5000   Nissan OEM BNR34 front bar in TV2  USED  $1000  Nissan OEM BNR34 front lower air spoiler  USED  $900  Nissan OEM BNR34 front lower air spoiler (painted)  USED  $900  Nismo front indicator (clear) USED  $80 Nissan OEM BNR34 radiator  USED $500  Nissan OEM BNR34 turbos  USED  $500  Nissan OEM BNR34 intercooler USED  $800  Nissan OEM BNR34 front swaybar   USED  $500  Nissan OEM BNR34 intake pipes   USED  $400    Also have a square set of uber rare Volk CE28n in 19*10 +22. Not really keen to sell these but make a high enough offer and maybe I will. If you don't know how much these usually sell for don't bother.   PM for pics.  Pickup Chadstone VIC or postage at buyer's expense.
    • waxracing
      Power steering pump r32

      By waxracing · Posted

      Thanks Mate, I did know you could do that but i know there is a pump out there that you can bolt on and it all lines up. I was told about it and then forgot the model, I figure if i am pulling it apart i will just put a new one on 
    • TurboTapin
      Power steering pump r32

      By TurboTapin · Posted

      You can also remove the veins from the HICAS portion of your existing pump. 
    • DatsunBanana
      Rear subframe stay bracket bolt removal issues

      By DatsunBanana · Posted

      Trying to swap the rear subframe on my R34 and can't remove the L-shaped stay brackets between the front subframe mounts and the sill/chassis. I'm in the UK so rust is a problem. I've used loads of WD40 and then Tunap 103 for days beforehand. I backed off the bolts forward a bit, backward a bit repeatedly for ages to try and avoid snapping. They have all moved a few full turns. The one I've spent most time on has come loose and I can turn with fingers, and it will pull down and push up 2-3mm. But it won't come out. I can tighten it back up and loosen it off again repeatedly but it still won't come out. I assumed there's a captive nut inside but if that's broken loose then I can't understand why I can always tighten the bolt back up - I'd expect it to just spin both ways. Any ideas what's happening here? I can't visualise what's inside there to cause this.
×
×
  • Create New...