Jump to content
SAU Community

Recommended Posts

Hi,

My mate just bought a 2002 model 200sx. It is fully standard and is automatic. I was reading that they go 0-100 in 5.6 seconds standard. I have a R32 manual and i read that they go 0-100 in 6.5 standard. The mods i have are:

R34 Turbo - Running on 7psi

Lighten Flywheel

3 Inch Excust

K&N Air Filter

Front Mount Intercooler

I was just wondering if you guys think I can beat him with the mods I have?

Link to comment
https://www.sau.com.au/forums/topic/117627-r32-skyline-vs-200sx/
Share on other sites

Personally i think it will come down to driver.. the auto will be quicker off the mark however it depends on how well you know to drive your car. stock 200sx has around the same rw/kw as a stock R32 however the RB20 should have more torque. The auto 200sx are pretty laggy until 4000rpm... Considering your mods you should be able to get him, if not let me drive your car :) hahaha just kidding... the only way to find out is down the 1/4 mile.

Regards,

Sarkis

You will chop him very very hard with those mods against an stock auto s15. You have manual vs auto, a bigger turbo and modifications done!

Standard the s15 sr20 would have quiet alot more torque than a standard rb20 though Sarkis.

Anyway go and find out mate, im sure you'll be happy with the results :)

Accordin to most dyno's and Nissans figures the sr20 has more torque, maybe due to more compression in the motor or 4 bigger pistons compaired to 6 smaller ones? Who knows but from what ive seen sr20 does have more torque (more noticable off boost than on)

actually remember that in australia the s15 sr20det was detuned from the factory. and in manuel form will do 6.34 and a standing quarter of 14.59.

Australian spec s15 has 147kw and 265nm of torque@48000rpm. Rb20 got few more KW's but same torque. S15 manuel weighs in at 1282kgs.

about the same asa 32

R32 Manuel will do 6.5 and 14.8 quarter. Expect only 0.1 to 0.2 seconds slower for the auto s15.

If your mate got rid of nissans state of detune he would be making 187kw and be running 13.8 quarters.

Youll woop him if you can drive properly if you got those mods you listed

They're no chance in hell a stock S15 can run 5.6 0-100km/h taking into account the car is an australian model and is auto.

The Jap S15 came with a ball-bearing T28 as opposed to the plain bearing of the Aus S15's.

Taking into account your mods I'd say you'd beat him easily. But mate why don't you just go out and have a run? Its all fun and let us know how you go.

Japanese spec S15 manuals ran 0-100 in about 5.6 as you stated - they have 184kw as standard. The Aussie cars were detuned to 147kw, and do 0-100 in low 6's in manual form. The auto's are slower again, with 0-100 in the 7's. A stock R32 GTST manual would chop a stock S15 auto very easily.

But then that raises another question - why are you running LESS boost than a stocker? Dunno too much about modifying cars, but your set up seems good for around 1 bar boost if you ask me! BOOST THAT SUCKER UP!!!

Edited by Big Rizza

Thanks Guys,

Ive ordered a boost controller and should be getting a new fuel pump in the next 18 days. My mate wants to have a drag in about 2 weeks so hopefully I will have it boosted when we drag. Although I should be able to win with it running on 7psi. I wont be happy if he does beat me. I might have to practice my take offs. Could i turn the boost up a bit without the bigger fuel pump?

Thanks

Yeah i will proberly run it on 10psi when i get the boost controller.

But then yesterday when I was driving the metal plate that holds my clutch in position snapped. So now i gotta take out the clutch pedal and cylinders to fix it all up. Hopefully it will be a easy job and somewhere will have the brackets to buy. Has anyone installed a Clutch pedal before?

My mate got his 200sx back the other day and wont take me for a drive. He has taken everyone else but me. I think he doesnt wanna show me how quick it is becasue it might be slower. Im pushing him to take me but my mates who have been in it say that mine is quicker anyways.

Also some how the bracket that holds my clutch twisted and snapped. Not sure if becasue it was mounted wrong or because the heavy duty clutch was to much pressure. I bought a new one which cost me $220, hopefully I wont have the same problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...