Jump to content
SAU Community

Recommended Posts

Hi Guys,

I had a very clean and straight R34GT-T, until some silly bitch ran up the back me at full speed on Sunday.

It was a f**kn hard hit, so hard the van she was driving buckled it's roof.

The rear end of my cars totalled and there's some minor damge to the chassis, (suspensions OK) about 15K damge.

My panel beater (who's very good) tells me it will fine and I'll never know it's been in an accident.

I'm not so sure, I really worry about cars once they've been in a hard it like that, with chassis damge.

I'm wondering should I keep the car, or just sell it once I get it back?

Thanks

Any chassis damage is bad for the car. If the repairer is good, you shouldn't be able to tell it hasn't been in an accident. 9 times out of 10 though, it won't feel the same again.

Just see how it is when you get it back. Hopefully all works out nicely for you :D

Edited by d0p3y
Any chassis damage is bad for the car. If the repairer is good, you shouldn't be able to tell it hasn't been in an accident. 9 times out of 10 though, it won't feel the same again.

Just see how it is when you get it back. Hopefully all works out nicely for you :D

Thanks for the reply,

Yeah that's pretty much I thought. I've taken it to an exceptionaly good Prestige Panel Beater, so I guess I'll just have to hope for the best!

best bet i think would to be to sell it after its been fixed up if your still not happy with how it feels.. i wouldnt pull the dodgy on someone though, but if your not happy with the car your driving, then whats the point? you wont enjoy it so much

hope it does turn out ok though. a hit from behind, i would have thought would be the best spot to get hit if any. if it was hit side on just hard enough to do a bit of chassis damage it would put the whole car out of line, or the same with the front or a corner.. where as the back, no engine, and less chance of making it out of line.

From my experience high quality repairs are better than factory building. Spot welds done by a human way excede robots. Chassis rail bends are not really a problem if repaired or replacements are done properly.

Don't think of selling it till you at least put a good deal of kays on it. You need to see how the tyres wear.

Neil.

That's true, and get someone to drive behind you for a bit to see if the car is driving straight or not. I had a friend tell me my car drove like a crab so we swapped cars and it seriously did look like it. (it wasn't the line)

Also I know of another r34 that got hit the same way, car was doing about 60-70 and hit the line which was stationary. The line was written off.

Thanks guys,

Some good points, makes sense.

Thankfully it looks like the car will be written off, my panel beater seems pretty dam sure of this, the chassis and suspension are both damaged.

We'll see what the insurance assesor sais tomorrow morning!

From my experience high quality repairs are better than factory building. Spot welds done by a human way excede robots. Chassis rail bends are not really a problem if repaired or replacements are done properly.

Don't think of selling it till you at least put a good deal of kays on it. You need to see how the tyres wear.

Neil.

I don't doubt what you say; if you find a good shop and they spend the time then I'm sure you'll have no problems. However, I think the problem is probably mostly placebo (or a poorly done job); because you know the car has been shunted there is always that nagging doubt.

You're also likely to loose out on reselling due to repair (any buyer worth their salt will either walk away or try and use it to bargin), so having it written off is probably a good thing for most people.

Yeah, I totally agree. If I looked at a car that had any sign off a hard hit I'd simply walk away, wouldn't even bother trying to bargain.

The insurance assessor has had a look and just need to crunch the numbers, so hopefully it'll be writen off :)

Yeah, I totally agree. If I looked at a car that had any sign off a hard hit I'd simply walk away, wouldn't even bother trying to bargain.

The insurance assessor has had a look and just need to crunch the numbers, so hopefully it'll be writen off :rolleyes:

:) BARSTARD, The assessor has instructed the panelbeater to repair it.

Panel Beater assues me he will take his time do the job properly, and it will be good as new.

Guess I'll have to hope for the best!

:D BARSTARD, The assessor has instructed the panelbeater to repair it.

Panel Beater assues me he will take his time do the job properly, and it will be good as new.

Guess I'll have to hope for the best!

D'oh.

If you feel strongy about it why don't you appeal? You're the one being put out and you're not at fault. Can't you request another assessment by another assessor?

:P BARSTARD, The assessor has instructed the panelbeater to repair it.

Panel Beater assues me he will take his time do the job properly, and it will be good as new.

Guess I'll have to hope for the best!

Hi,

Don't agree to it. Remember, the assessor you are dealing with is the assessor for the at fault driver.

My recommendation is that you get your insurance company involved and ask their assessor to assess the car. It won't cost you anything and you won't have to pay an excess.

I was in the same situation a while ago where my car was stationary and hit hard from the rear.

The panel beater said he can fix it like new and this is what the at fault assessor wanted to do also.

I contacted my insurance company. I expressed concern on the structural integrity of the vehicle and my insurance company assessor had the car written off.

The minute there is talk of chassis damage the structural integrity of the vehicle is in question.

I would not accept any compromise on my safety or the safety of any passengers.

Contact your insurance company, they are looking after your interests.

Good luck

Cheers

Jo

Assessors are all supposed to be independant but there is often influence. Doesn't matter if their insurance company is not trying to exert the influence, the assessor might feel it anyway.

I was going to bring up Jo's car before since the situation is almost identical (4 door r34 hit from behind, question over whether it should be a write off or not) but I forgot. Luckily she found the thread!

  • 1 month later...
When I put in my claim form I actually wrote on the cover sheet of the fax that I would like for them to push for it to be written off.

Maybe you should talk to your insurance co about it mate.

The assessor is from my insurance company, I lodged a claim with them and have been dealing with them directly, since the beginning.

I stressed my concerns and asked for it to be written off from word go, but I guess at the end of the day their just interested in the numbers.

Car should be ready ina few weeks, my panel beater is still adoment the car will look and feel exactly the same, just have to hope the best I guess!

The assessor is from my insurance company, I lodged a claim with them and have been dealing with them directly, since the beginning.

I stressed my concerns and asked for it to be written off from word go, but I guess at the end of the day their just interested in the numbers.

Car should be ready ina few weeks, my panel beater is still adoment the car will look and feel exactly the same, just have to hope the best I guess!

Be completely anal do not accept anything that isn't to your liking...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...