Jump to content
SAU Community

25t Intercooler Questions

GTS25-t

By GTS25-t,
in Engines & Forced Induction

 Share

Recommended Posts

GTS25-t Apprentice

GTS25-t

Posted
Posted

Ok, ive only recently gotten myself an R33 GTS25t and im looking at modding it a bit, problem is im not too clued up on all the finer points of turbo cars. The first thing will be the 3" exhaust, but now im looking at an intercooler.

Firstly, what coolers can i get that use the factory pipes? (with extensions etc), and are there FMICs avaliable that have the entry and exit on the same side? (i think ive seen them somewhere before, but might have just been a twin entry)

Secondly, if i decided to get a full cooler and piping kit, what size cooler would i be looking at so i dont have to hack up much of the stock front kit? (its a facelift model). And also, for people who have done this, is there a noticable increase in lag?

Any help you guys can give me would be appreciated, cooler dimensions would be a big help. Sorry if this has been covered a million times, i did try searching!

Link to comment
https://www.sau.com.au/forums/topic/118136-25t-intercooler-questions/
Share on other sites
Wink Grand Master

Wink

Posted
Posted

ARC coolers have inlet/outlet piping on the same side.

Whatever FMIC you get, you will have to hack up the behind of the stock series 2 bumper - there's just not enough space.

With my FMIC I don't notice any increased lag.

GTS25-t Apprentice

GTS25-t

Posted
  • Author
Posted

What size FMIC do you have wink? Also should the intercooler piping be 2.5 inch or 3? The intercooler kit im looking at has 2.5 inch pipe but uses silicon reducers to fit to the 3" inlet and outlet on the end tanks.

BezerkR32 Veteran

BezerkR32

Posted
Posted

there is a thread on page 1 about intercooling that will be worth reading for you.

Just note that with cooler quality, and anything really, you get what you pay for. The cheapest always isnt the best option.

Ok, ive only recently gotten myself an R33 GTS25t and im looking at modding it a bit, problem is im not too clued up on all the finer points of turbo cars. The first thing will be the 3" exhaust, but now im looking at an intercooler.

Firstly, what coolers can i get that use the factory pipes? (with extensions etc), and are there FMICs avaliable that have the entry and exit on the same side? (i think ive seen them somewhere before, but might have just been a twin entry)

Secondly, if i decided to get a full cooler and piping kit, what size cooler would i be looking at so i dont have to hack up much of the stock front kit? (its a facelift model). And also, for people who have done this, is there a noticable increase in lag?

Any help you guys can give me would be appreciated, cooler dimensions would be a big help. Sorry if this has been covered a million times, i did try searching!

Munna1 Proficient

Munna1

Posted
Posted
Ok, ive only recently gotten myself an R33 GTS25t and im looking at modding it a bit, problem is im not too clued up on all the finer points of turbo cars. The first thing will be the 3" exhaust, but now im looking at an intercooler.

Firstly, what coolers can i get that use the factory pipes? (with extensions etc), and are there FMICs avaliable that have the entry and exit on the same side? (i think ive seen them somewhere before, but might have just been a twin entry)

Secondly, if i decided to get a full cooler and piping kit, what size cooler would i be looking at so i dont have to hack up much of the stock front kit? (its a facelift model). And also, for people who have done this, is there a noticable increase in lag?

Any help you guys can give me would be appreciated, cooler dimensions would be a big help. Sorry if this has been covered a million times, i did try searching!

If you dont plan on upgrading your stock turbo a R34 GTT cooler is a good option efficent for 200rwkw. Direct bolton no mucking arround with piping and cheep. Since your new to this either cheekout the R33 tuning guide at the website in my sig or do a search mate

cheers

Wink Grand Master

Wink

Posted
Posted
What size FMIC do you have wink? Also should the intercooler piping be 2.5 inch or 3? The intercooler kit im looking at has 2.5 inch pipe but uses silicon reducers to fit to the 3" inlet and outlet on the end tanks.

I have the Justjap Type 2 kit. It's 2.5" piping + end tanks

If you have 3" end tanks, you'll have to chop up even more of the front bar as the end tanks are the things which take up the most space on the bumper.

R3LOAD Community Regular

R3LOAD

Posted
Posted

Just go for a GTR sized intercooler of whatever brand you wish, not sure what the exact dimensions are but im sure someone can tell you.

You'll need to do a bit of cutting into the back of the front bar but it shouldnt be anything too major.

Kaido_RR Grand Master

Kaido_RR

Posted
Posted

do it right, do it the 1st time buy a jap kit. I have a china/hybird kit and would advise against them the fit is shocking...

ARC,Blitz both have the piping returing to the stock holes.

Hks,Greddy need you to cut a hole near the waterbottle and have the piping running that way.

QRI05E Mentor

QRI05E

Posted
Posted

Im tossing up between a 600 x 300 x 76 or the 600 x 300 x 100 (Gktech) FMIC... considering the car has stock turbo and ecu i think the 76mm thick core is more then enough however i will be going larger turbo and PFC end of the year.. will the 76mm core handle 280 - 300rw/kw??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Ahh. Well the block damage is a problem, you really need to run a tap or thread chaser through it to see if the threads can be saved, but any chips are likely to be bottom end bound which is bad. Earls seem to have what you need if you want to stick with mounting direct on the block: https://rceperformance.com.au/parts/earls-straight-adapter-1-8-npt-male-to-1-8-bspt-female.html, but as I said above I'd recommend remote mounting the sender
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm not quite understanding or I'm missing steps here, (I appreciate people are trying to inform my brain but I am of the dumb, especially today) - All I want to do is mount the male BSPT of the OEM sender into the system somewhere without it snapping the adapter via vibration. The Nissan sender has a male 1/8 BSPT output. The block has a (very destroyed) 1/8 NPT input. I'm not really sure how a lathe assists with that, and also don't know anybody with a lathe, nor specifically what I would want to buy. I'm not really sure how adding additional adapters creates a better, more leak proof resilient seal here.
×
×
  • Create New...