Jump to content
SAU Community

Recommended Posts

Guest one8tee

Hello everyone, I've finally acquired an R33 GTS-t Series 2(saving up for that GT-R):D

Been surfing the forum for awhile now, but I can't seem to find much info on this "A-LSD" thingy. It's in the speedo, next to the word "Slip". I heard from some people that it's some form of traction control for the R33.

Anybody out there encountered this before? Any feedback on it's good/bad points? Can it be turned off??

Thanks.

PS:Also I've noticed there's not alot of bodykit options for the Series II(from what I've seen), especially for the front-bar. So would any series 2 owner out there care to shed some ideas?

cheers all.

and LSD is a LIMITED SLIP DIFF

it makes it so both wheels spin. therfore putting more power to the ground.

its not electrong and its not traction control(ignition cut), authough it does control wheelspin.

all r33 gtst's have lsd's

most commodores have open center diffs which means only one wheel will spin.

main reason ppl think their commodores are tough. (wheel spinning)

the lsd enables u to put power more evenly to both wheels authough it is not 50:50 power.

if u wanted 50:50 u woudl have to look into a weld job or mini spool or full spool or detroit locker.

i have both active lsd and slip... i am pretty sure they both come together and are very very rare on all r33's apart from gtrs. the slip indicator light comes on when the rear wheels lose the slightest bit of traction, even before you can feel it. It is not traction control, traction control backs off the throttle to help regain traction this simple lets you know that u either are losing traction or have no traction.

Motox was pretty good with his explination however i think he missed a point where the active lsd enables one wheel(i think thi is correct) to spin faster then the other one thus puting more power to one side of the car this is extreemly helpful when the back goes out. You dont even have to really fight with the steering the car just pulls itself in rather easily.

And also if you want to see how special you are have a look inside your boot on the right hand side, you'll have a little resivour(spelling???) for the alsd which other r33s wont have :D and also have a look under the back of your car then have a look under someone elses car who doesnt have these features their car will look bare compared to yours. :D

i already know the a stands for active lsd do a search on this, ive started a threrad about this before... it is extremely rare ive heard it was a feature which cost an extra 15k but im not sure how true that is.... anyway you are very lucky to have these features as am i! :P

My R33's door lock when i shift my gear to 2nd, is that a safety shit or some thing wrong with my car?[/quote

do a search on this topic!!!!!, what does that have to do with this subject, and also it doesnt do it when u shift into second it does at when u hit 25km/h it is for safety obviously!

if your unsure start a new thread but dont whore others

A-LSD: As already explained, stands for Active Limited Slip Differential. It's the same system as used on the GT-R.

In a nut shell it uses a computer controlled rear limited slip diff that transfers a percentage of power from left rear to right rear or visa versa as required, thus maintaining best possible traction.

A-LSD wasn't so much an extra 15k cost option but rather a different spec of car on top of the GTS25t (this is for S2, S1 not sure?). When I get a chance I'll look up my R33 S2 price guide. I've got the new car prices (in Yen) from bottom of the range through to N1. The A-LSD GTS25t is listed above the GTS25t & IS dearer. I'm pretty sure it's not 15k dearer though!?

As akeenan posted above, the passenger door lock function is a standard safety feature. When the car exceeds 25km/h it locks.

I HAVE ONE OF THESE!

Don't break the diff.. It's extremely hard to get a replacement and extremely expensive to fix. Seeming they are soo rare no one really knows alot about them. I have been informed they are basically a GTR diff with different ratios. SOO... I have just opted to get the diff in my car fixed.

I see the slip light come on fairly often :angel: ... But never really seen the A-LSD light... Is this good or bad? :confused:

It looks pretty tough but when someone is in the car for the first time and the wheels spin and the light comes in. Straight away their question is "What... thats soo rhad?!@" ... I just shrug cause I'm used to it now :)

Oh yeah.. BTW my car is a series one with quite a few series two bits.

Originally posted by GTS-t VSPEC

The A-LSD light should only come on if there is a problem with it.

My series 1 has it, it's a cool feature, makes you braver when cornering fast, as you are sure the back-end will correct itself.

See'ya:burnout:

it also comes on when you get it majorly sideways. :(

mates 33 in perth also has it.. i read somewhere there were only 100 released, it seems there's a few people on here with them though.

Shaun

OK this is from the original 96-97 Nissan pricing info:

Coupe:

*NOTE* - Type M means turbo (it isn't an up spec version of the GTS25t!)

GTS25t Type M 5sp - 2,916,000y

GTS25t Type M Auto - 3,013,000y

GTS25t A-LSD (5sp only) - 3,196,000y

Interestingly enough the GTS25 Type S Auto (RB25DE) was more expensive than the Type M 5sp (RB25DET) @ 2,928,000y !

97 GT-R N1 - 6,096,000y

4 Doors:

GTS25t Type M 5sp - 3,225,000y

GTS25t Type M Auto - 3,322,000y

GTS25 Type S Auto - 2,850,000y

The GTS25t A-LSD Type M (that's how it's listed!) is heavy than the GTS25t 5sp or auto (1370kg - 5sp 1390kg - auto 1400kg -A-LSD 5sp) It also came standard with 205/55/16 F 225/50/16 R.

S1's (93-94) & S1.5's (95 models) with the A-LSD I have no info?

My 9/94 model doesn't have the A-LSD but it does have ABS :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...