Jump to content
SAU Community

Buying A Car Indirectly...

mikymouse

By mikymouse,
in Victoria

 Share

Recommended Posts

mikymouse Rising Star

mikymouse

Posted
Posted

Hi. I am about to make a deposit on a Nissan Silvia. However, the person who I am purchasing it through is selling it for his dad, who has moved to Queensland. The car is registered in the dad's name. I will be buying it unregistered.

What can I do to ensure the deal goes through smoothly? Will I need to have the son provide a signed contract from his dad? Will he signing it for his dad be enough?

The last thing I want, is to buy the car, then have it reported as stolen by the dad when I go to register it.

Thanks in advance guys.

Link to comment
https://www.sau.com.au/forums/topic/118996-buying-a-car-indirectly/
Share on other sites
RCHOO Grand Master

RCHOO

Posted
Posted
Hi. I am about to make a deposit on a Nissan Silvia. However, the person who I am purchasing it through is selling it for his dad, who has moved to Queensland. The car is registered in the dad's name. I will be buying it unregistered.

What can I do to ensure the deal goes through smoothly? Will I need to have the son provide a signed contract from his dad? Will he signing it for his dad be enough?

The last thing I want, is to buy the car, then have it reported as stolen by the dad when I go to register it.

Thanks in advance guys.

Go on ya gut if ya dont feel right dont do it...

If want to be safe i would...

1/ make sure the vic roads paper work looks good (rego papers)

2/make sure there signed in his dads name

3/ask to talk to his dad by phone(hes only in QLD not the moon)

4/Ring vic roads and make sure all fine

5/Pay by bank cheque( in the owners name) not cash

^ oh yeah make sure its got compliance plate.................good luck buddy

Beeble Community Regular

Beeble

Posted
Posted

Selling it for his dad? or possibly the car belonged to the kid, was driven by the kid, maintained by the kid, and the rego is in dad's name so the insurance can be in dad's name and the kid can save some $$$? :)

I'd want at least a faxed (signed) letter from the father allowing the kid to sell the car and act as a proxy, and DEFINATELY talk to him on the phone and make sure it's all kosher.

in all honesty though, i'd put my money on the car actually belonging to the son, and it was just registered in dad's name to make insuring it easier!

my 0.02c

R33-Lovr Enthusiast

R33-Lovr

Posted
Posted
Are you sure R33-Lovr? I have spoken to a few people and they seem the have the belief that if you have a letter from the father giving permission for the son to act as a proxy in the sale, that is acceptable.

Yep am sure i had my previous R33 under my mums name whos a pension when i came to sell it i rang the RTA (NSW) and asked would it be possible for me to sign in the blue slip on behalf of my mother with a letter attached from her saying i could sell register the car on her behalf and they said no, i only asked them because i already had a letter from my mum signed to do so but it was no use.

i could only register the car but cant sell it.and i still had to provide her pensioners card.

Maybe its different in Vic best thing to do is ring your Road and traffic authority, i think they r callec Vic road or something but thats how its in syd.

beefy Proficient

beefy

Posted
Posted

Trying to remember back from when I bought my car...

You should check if there is any finance remaining on the vehicle. Even if you buy the vehicle from them , if they skip the country the finance company can reposes the car. Ring Vehicle Securities Register (13 11 71)

For a small fee you can receive a certificate that I believe will protect you from repossession. Well worth it. I think it cost me $8

Check with Vicroads if the vehicle is in the Stolen Vehicle Database.

Good Luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...