Jump to content
SAU Community

Recommended Posts

guys and gals, make sure yas watch out if ya ever have to replace a window motor in a r33, i was just doing mine and when i took the motor off it sprung back onto my thumb and nearly chopped it off!!!! arrrrr, i could see tendans and nearly to the bone, just required 6 stiches, just a word of warning to anyone that ever goes to change a window motor!!

Cam. :(

(watch that spring)

Hahah thanks for including chicks in that statement but we are smart enough to get some other poor unsuspecting person to do it for us haha but if a mechanic ever does a bad job and i need inflict an injury i'll keep it in mind! :(

P.S: Hope ya finger gets better :O

bwahhaah thats classic, im glad someone out there also hurts themsleves when working on the car. I thought i was the only one.

Had a small injury today where i wanted to test if the ciggie lighter was working properly, needless to say my finger has a nice sized blister on it now. :P

Bwhaha i saw my dad shove a screwdriver into his brain via a nostril once. Wasnt so funny at the time with the amount of blood and all but dam i had a good laugh after the catscan was done adn nothing was wrong. I think i get my accident pronness off him actually.

Did you buy that motor from Dr_Drift?

I was there when he took it off the window assembly, and boy did it fling out. Lucky for him, he used his foot to hold down the rails while he unscrewed the motor. Once that last screw was out all hell broke loose.

Sorry for not thinking of putting up a thread, i know for next time.

aw11, I did sorta the same thing ... cept my mother stole the power cable to the computer, so instead of doing the smart thing and realising that the kettle used the same cord type, I used three coasthangers which I bent out (I was only like 12, gimme a break) ...

Well, you guessed it it was all working fine until I decided my hand belonged next to me instead of on the desk, course the computer was also next to me with streaming 240 volts care of the coathangers ....

Hand went down, thankfully safety switch caught it, however hand went up straight into a running fan ... felt the electricity go down my arm and to my chest, arm and hand was numb for a good 5 mins or so, only after did I reliase how much damage the fan did to my fingers :P

hehhehe, im not used to typing with one hand, i can sort of use my right hand, but its a bit difficult, as its bandaged up.

Al: yeah it was the motor that i got off Dr_Drift, dont matter ill be rite, just temporary loss of use of my right hand, hahaha :(

Macka: if ya dont have to unscrew the 3 screws that are on the motor you'll be rite as it only springs back when u take those screws out

rs73: did you want a pic of the actual motor? i can take one and PM it to you if u want.

Boostzor: its the first bad injury ive had while working on the car, hehe, but im sure there are plenty more to come.....:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...