Jump to content
SAU Community

Recommended Posts

'

Matt!! <3

buy my IS and drop a 1j in it :)

kthxbai

<3

sorry, effort is too large, will wait a bit till i get sick of the is and buy an s15 or rx7....

group buy on car and parts though...

NGK BCPR6ES(-11 or -8)...best for rb25's imo..they come standard in 1.1mm gap and .8mm gap...depends on what boost your running as to what plug you should chose...standard boost 11 and 10+psi 8.

u ebtcha :) Oh i dunno

awww come on man :)

NO leave me alone you freak

ive always thought 5000k and they r haddit

Well i noticed a while back it started missing when idling, and it wasnt going as hard as it use to.

So yeah probly check them each oil change.

4-album set, 314mb of Punk.

Punk goes 80’s, Punk goes acoustic, Punk goes metal and punk goes pop. I have far too much punk to listen to. Manic Monday by the bangles and Straight up by Halifax FTW so far

Wot...No Slim Dusty. :):)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...