Jump to content
SAU Community

Recommended Posts

ahaha josh i LOL when i read the blow it out lol

put a set of forgies in a ca18 and it will be a lot tougher then an sr with forgies and nothing else

lol why cause its a cast iron block.. lol i think not anyway.. CAs are shit lol.. i hate them.. i put RBs into ca equiped cars and send them on ther way...

minus the headgasket issue's ca's are prone for :(

yep they sure r.. that crank angle sensors and case seals.

and premature build requirements on a ca, had endless ca's with headgasket issue, could be due to the fact that most are 15yrs old n well an engine that old isnt going to have the best gasket material quality :(

Re: people who budget build.

Why use cheap shit. Do it right and use something decent.

and premature build requirements on a ca, had endless ca's with headgasket issue, could be due to the fact that most are 15yrs old n well an engine that old isnt going to have the best gasket material quality :(

lol reminds me of a post i read on the forced induction section bout a fella with a RB25DE that had a WEETBIX LID for a head gasket.. or somehting like that.

Re: people who budget build.

Why use cheap shit. Do it right and use something decent.

as if.. use supertool shit and wait supa tool i think its called. and shit that cost less than genuine.

haha just get ur standard pistons throw them in ur fireplace overnight with a log roaring she'll be forged in the morning.

your keen. they got it at drive ins this weekend. tandem showing, simpsons movie and knocked up....would be good viewing

knocked up was pretty shit i thought

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I hope it's actually possible. This is a write off in insurance world.
    • Yup. 2-way with shallow ramp angles. Still works.
    • That was the first session so not a lot to take from the day. It was low 20s ambient and the coolant had got to 110 (and obviously had some pressure!) so that still needs to be addressed. I haven't downloaded the data yet but will. I had refilled the auto trans with Redline DT6 because it claimed the best viscosity I could find at 100o. It wasn't really long enough to get a good feel for that; while the trans got to 100o in the session it still wasn't shifting crisply as I hoped. I think I'll try a few more sessions before judging. No steering motor overheat but I'd hope not in only 1 session! But finally the suspension; it was night and day over the standard stuff and the car was a couple of seconds quicker on the same crappy tyres, which is a huge difference. I'll stick with that and get some sway bars and a mechanical diff sorted too and see how that all goes together
    • I guess it’s partially a compromise of how my car is used, wanting to be able to switch from drift to grip with track side on-car adjustment. Also partially with the way the knuckles are set there is more static camber but less dynamic camber gain. 
    • OK, so update from the track day on Friday It was a classic "an unfortunate series of events'. There were a few cars around and when i checked my mirror coming out of the fish hook I notice some smoke from the rear of mine. Looked again and it was getting much worse, I figured I'd blown a turbo or something to got off it and pulled off the racing line. However.... since it is a left hairpin into a right kink, I was on the inside of the next corner. There was a car passing me on the left and a big drop off over the ripple strip on the right......and someone had knocked the witch's hat that was on the apex about 1m onto the track. So, between those 3, I decided to mow down the cone and not damage my car/the other car. Right choice, but surprising result.  The car decided the cone was a small pedestrian so it blew the rear bonnet hinges up to protect their head in the upcoming person to car impact....I didn't see that coming and like an airbag deployment it happened super fast. Straight into the pits from there, everything was driving fine but it became clear it was a coolant leak not smoke, it was billowing up onto the windscreen. Onto the trailer and home. I'll do a separate thread about the repair (once I work out what it is ), but the immediate problem was the bonnet wouldn't open because the front was pinched onto the front bar and would not release. Ultimately we unbolted the hinge from the bonnet, pulled it back a little and it released from the front OK. "There's your problem", the top radiator hose had popped off at the radiator.
×
×
  • Create New...