Jump to content
SAU Community

Recommended Posts

If it the one I am thinking of I think you will find it quite gone

Lol worst tyres ever, luckily you are only destroying them

yeah its gone.. need some standard RB25 cams..

well they wer 70% now.. around 5% and delaminated heaps.. i melted the insides quite bad.. and i can see how much neg camber on the back i have.. the outside look like 60% and insides are shit.. thats just from 2 hours of practice. fark my exits are getting good.. its my damn entrances and a lil clutch slip...

not too mention a bit of understeer it gets sometimes..

what r u laughing at?

BTW did i tell u ive got that tow truck booked for tomorrow morning for u to do that roll cage? :)

No worries mate...ill start and finish it after work today, 4-5 hours should be plenty of time, might even have enough time to have it painted also. haha.

Spare box you wont need...just a spare set of dog rings.

Hi guys, Whats happening?

had a great weekend went out to Norwich Park mine near Dysart (3hrs west of Makay) for a work thing. the coal mine had an oepn day was good to go see all the man machines!!! went in a dragline was tuff as got lots of pics will put up later

where do you slide Mark???

Street or track?

atm industrial area nothing special.. :D i never do anything stupid anywher near other traffic.. thats just not right.. and never near other residential areas.

start hitting the archerfield track soon. as soon as i fix this understeer problem.. :3some: any ideas.. thinking castor rods and 7 on thefront.

yeah its gone.. need some standard RB25 cams..

well they wer 70% now.. around 5% and delaminated heaps.. i melted the insides quite bad.. and i can see how much neg camber on the back i have.. the outside look like 60% and insides are shit.. thats just from 2 hours of practice. fark my exits are getting good.. its my damn entrances and a lil clutch slip...

not too mention a bit of understeer it gets sometimes..

i have a set of rb25 cams...

i told a girl to f**k off she cant hang with us all the time and she got shitty.. if i told shane he would try to hump me.. why r girls different/?

caus u smell funny? :3some:

No worries mate...ill start and finish it after work today, 4-5 hours should be plenty of time, might even have enough time to have it painted also. haha.

Spare box you wont need...just a spare set of dog rings.

ur a good worker michael, u'll go along way :rofl:

bahaha when i rang that bloke to ask about boxes, he asked how u n ur dad were going with the box, and he said they'd last alot longer if the driver knew how to shift properly :D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...