Jump to content
SAU Community

Recommended Posts

Mr Ants, here is a well interesting article on the problem I experience and had discussions with you about. His before CAS signal plot looks just like mine! http://www.skylinesaustralia.com/forums/topic/384932-new-rb-parts-with-results/

Also may have solved my computer issue for a lot cheaper than I thought so it may get done earlier now!

Mr Ants, here is a well interesting article on the problem I experience and had discussions with you about. His before CAS signal plot looks just like mine! http://www.skylinesaustralia.com/forums/topic/384932-new-rb-parts-with-results/

Also may have solved my computer issue for a lot cheaper than I thought so it may get done earlier now!

that's positive news Bunts

not much except that he endorses it and is well experienced in tuning it.

Cool I thought as much, he recommends Wolf but only because he can personally get them the cheapest or somthing along those lines, he told me that any of the top teir ECUs are fine by him

that's positive news Bunts

In regard to that article I dont actually expect you to have the same issues because all your timing gear is newer, but it will be a really interesting tune to watch in that regard

Ya it is, Just tracking down info on the ECU now but it seems all good.

Edited by Bunta

Yeah, also I know Paullie runs a Ross crank trigger kit. He also makes 470rwkw with -5s so I can understand why he has it.

Yeah that will be the main difference, I just cant justify paying the money for the Ross kit, and Dan recently had issues with several Ross balancer's apparently the cranks were full of tiny little cracks from a dodgy balancer.

Hay guys just stop in to say hello =)

Hello

Cool I thought as much, he recommends Wolf but only because he can personally get them the cheapest or somthing along those lines, he told me that any of the top teir ECUs are fine by him

In regard to that article I dont actually expect you to have the same issues because all your timing gear is newer, but it will be a really interesting tune to watch in that regard

Ya it is, Just tracking down info on the ECU now but it seems all good.

in the event those jitters crock up I will install that trigger disc. Hopefully that will help.
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...