Jump to content
SAU Community

Recommended Posts

Member name

Posts

shanef

8170

Nismo_Boy

5062

Silver_R34_GT-T

4271

Bunta

3769

Ants

3170

phatboi2010

3131

Captain Natro

2779

Keegs

2658

luke GTR

2501

t5iv

2486

Col-GTSX

2425

markimak

2389

Mr-Toy33

2331

impact_blue

2273

lilmike86

1965

LIL34

1947

SMR33

1894

Konrad

1894

FineLine

1879

Oblivion

1334

85URK

1333

Squizz

1174

cowdy

1139

SLO-89

1028

Cadmoon

1026

Member name Posts shanef 8170 Nismo_Boy 5062 Silver_R34_GT-T 4271 Bunta 3769 Ants 3170 phatboi2010 3131 Captain Natro 2779 Keegs 2658 luke GTR 2501 t5iv 2486 Col-GTSX 2425 markimak 2389 Mr-Toy33 2331 impact_blue 2273 lilmike86 1965 LIL34 1947 SMR33 1894 Konrad 1894 FineLine 1879 Oblivion 1334 85URK 1333 Squizz 1174 cowdy 1139 SLO-89 1028 Cadmoon 1026

7th of all time... I'm happy with that :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...